MGDQ1-00017 Tyco Electronics, MGDQ1-00017 Datasheet - Page 3

• Manufacturer Part Number: MGDQ1-00017
• Description: INDUCTOR 120UH .31A 20% SMD 6530
• Manufacturer: Tyco Electronics
• Series: MGDQ1r
• Type: Drum Corer

Specifications of MGDQ1-00017

• Inductance: 120µH
• Current: 310mA
• Current - Saturation: 310mA
• Tolerance: ±20%
• Dc Resistance (dcr): 1.9 Ohm Max
• Package / Case: 0.256" L x 0.272" W x 0.118" H (6.50mm x 6.90mm x 3.00mm)
• Mounting Type: Surface Mount
• Operating Temperature: -40°C ~ 85°C
• Frequency - Test: 100kHz
• Applications: EMI Filter
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Shielding: -
• Q @ Freq: -
• Self Resonant Freq: -
• Current - Temperature Rise: -

Environmental
General
Other
Chemical
Static Humidity
Storage Life
Temperature Cycle
Temperature Shock
IR Reflow
Storage Temperature
Range
Operating
Temperature Range
Flammability
Vibration
Mechanical Shock
Solderability
Component Adhesion
(Push Test)
Resistance to Solvent
Ionic Contamination
Item
For Print Distribution to Customers
B0
After exposure part remains within
specified electrical parameters for
L, Q and DCR.
After exposure part remains within
specified electrical parameters for
L, Q and DCR.
After exposure part remains within
specified electrical parameters for
L, Q and DCR.
After exposure part remains within
specified electrical parameters for
L, Q and DCR.
10 seconds at 260°C max.
-40°C to +85°C
-40°C to +85°C
IEC 695-2-2
After exposure part remains within
specified electrical parameters for
L, Q and DCR.
After exposure part remains within
specified electrical parameters for
L, Q and DCR.
Wetting shall cover 90% minimum of
each termination
Component shall withstand 6 lb. push
force minimum without delaminating
from mounting surface.
Conductivity:
pH:
Chlorides:
Sodium:
Potassium:
Specification
B0
Precondition at 25°C for 60 minutes. Expose parts to an environment
of +40°C with 90 to 95% R.H. for 240 hours.
Subject parts to an environment of 85°C 85% R.H. for 168 hours.
After exposure allow parts to dry for 4 hours before measurements
are taken.
10 cycles (Air to Air) 1 cycle shall consist of:
30 minutes exposure to +85°C
30 minutes exposure to -40°C
Allow 20 minutes transition between extremes.
10 cycles (Air to Air) 1 cycle shall consist of:
30 minutes exposure to -55°C
30 minutes exposure to +125°C
15 seconds maximum transition between temperatures
Post test parts shall pass all electrical specifications after reflow.
There shall be no visible signs of solder flow or leakage
from the part.
Withstands needle-flame test
1 cycle of 30 minutes of the following:
5 - 7 Hz constant displacement of 0.75 inches, 5 minutes
7 - 30 Hz constant acceleration of 1.5 Gs, 10 minutes
31 - 50 Hz constant displacement of 0.33 inches, 5 minutes
50 - 500 Hz constant acceleration of 1.2 Gs, 10 minutes
MGDQ1 Series - 500 Gs per axis, 2 directions
Dip pads in RMA
flux, 63/37 solder
(Sn/Pb) at 232°C for
5 seconds ±2
seconds.
Apply and measure force with a digital force gauge set.
Withstands 6 minutes of alcohol.
Withstands 3 minutes forced spray Freon TMS
11 µOhms/cm maximum
5.5 to 9
65 ppm maximum
20 ppm maximum
10 ppm maximum
Test Method/Condition
MGDQ1
Series
Sheet 3 of 3
Revision
B0