CH14MS-1D Cooper/Bussmann, CH14MS-1D Datasheet - Page 6
![FUSE HLDR ACC CH141 MICRO SWITCH](/photos/16/20/162042/ch_series_sml.jpg)
CH14MS-1D
Manufacturer Part Number
CH14MS-1D
Description
FUSE HLDR ACC CH141 MICRO SWITCH
Manufacturer
Cooper/Bussmann
Series
CHr
Type
Global Modular Fuse Holdersr
Datasheet
1.CHCC1D.pdf
(6 pages)
Specifications of CH14MS-1D
Accessory Type
Micro Switch
Product
Holder
Current Rating
40 Amps
Voltage Rating
750 Volts
Body Material
Polyester
Size (lxwxh)
79.54 mm x 45 mm
For Use With/related Products
Fuseholder; CH141
For Use With
FWX-10A14F - FUSE 10A 250V HS BOLT-ONCH141DNX - FUSE HLDR 1POS FOR 14X51MM FUSESCH141DNI - FUSE HLDR 1POS FOR 14X51MM FUSESCH141DN - FUSE HLDR 1POS FOR 14X51MM FUSESCH141DMS - FUSE HLDR 1POS FOR 14X51MM FUSESCH141DI - FUSE HLDR 1POS FOR 14X51MM FUSESCH141D - FUSE HLDR 1POS FOR 14X51MM FUSES
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
The only controlled copy of this Data Sheet is the electronic read-only version located on the Cooper Bussmann Network Drive. All other copies of
this document are by definition uncontrolled. This bulletin is intended to clearly present comprehensive product data and provide technical informa-
tion that will help the end user with design applications. Cooper Bussmann reserves the right, without notice, to change design or construction of
any products and to discontinue or limit distribution of any products. Cooper Bussmann also reserves the right to change or update, without notice,
any technical information contained in this bulletin. Once a product has been selected, it should be tested by the user in all possible applications.
Remote Fuse Monitoring Accessory – CH-PLC
UL Class CC, Midget and IEC 10x38 fuses
Description
A resetable three-phase remote fuse monitor that
integrates with a Programmable Logic Controller (PLC) or
other monitoring and control equipment.
Specifications:
• Power Input: 24Vdc / 5mA
• Sensing Voltage: 600V/30mA
• Output Signals: Digital 0Vdc (Low), 24Vdc (High)
• Rated Impulse Voltage: 8kV
• Local Indication: Two distinct LEDs indicate unit power
• Flammability Rating: UL 94V0
Wiring:
• For power, signal and ground connections use 22-24AWG
Emissions and Immunity Testing:
• Electrostatic Discharge IEC 61000-4-2
• Electrical Fast Transient/Burst IEC 6100-4-4
• Surge Immunity IEC61000-4-5
Packaging:
• The CH-PLC is packaged individually
• A single unit monitors up to three phases
• Package includes 0.11” (2.8mm) quick connects for power,
0210
- 0Vdc Low – Fuse is good
- 24Vdc High – Fuse has opened
When the fuse opens, the output signal is sent high and will
remain high until the unit is reset
(green) and open fuse (red). Upon the replacement of the
fuse, the actuation of the reset switch will reset the open
fuse LED
(0.25mm
signal and ground connections
© 2010 Cooper Bussmann
St. Louis, MO 63178
www.cooperbussmann.com
De-energize all circuits before installing or removing any CH-PLC devices and follow all prescribed safety procedures.
BU-SB10208
2
) 300V rated wire
Minimum Circuit Voltage:
• Minimum circuit voltage required across the CH holder is
Installation Technique:
• Mounts on the left side of the fuse holder and mechanically
IP20 Rating: Yes
Environmental Data:
• Storage and Operating Temperature: -20°C to 75°C
Agency Information:
• UL 508
• cULus to CSA Standard 22.2 No.14
PLC Programming:
• The CH-PLC signal line is designed to provide a digital
• Programmable Logic Control program must be written to
• The PLC program should check for consecutive high signals
100Vac for the remote indication device to operate
interlocks with the fuse holder switch handle with hardware
provided
input to a PLC I/O card.
properly interpret the input signal to the PLC.
before taking action on a critical process.
Page 6 of 6
Data Sheet 2053