ISL84051 Intersil Corporation, ISL84051 Datasheet
ISL84051
Available stocks
Related parts for ISL84051
ISL84051 Summary of contents
Page 1
... TTL/CMOS logic compatibility when using a single +3.3V ± and +5V supply or dual 5V supplies. The ISL84051 multiplexer device. The ISL84052 is a dual multiplexer device. The ISL84053 is a committed triple SPDT, which is perfect for use in 2-to-1 multiplexer applications. Table 1 summarizes the performance of this family. ...
Page 2
... Pinouts ISL84051 (SOIC, SSOP) TOP VIEW NO1 1 16 NO3 COM 3 NO7 4 13 NO5 5 12 INH 6 11 LOGIC GND 8 NOTE: 1. Switches Shown for Logic “0” Inputs. Ordering Information TEMP. o PART NO. RANGE ( C) PACKAGE ISL84051IB - SOIC ISL84051IA - SSOP ...
Page 3
... ISL84052 INH ADDB ADDA ISL84051, ISL84052, ISL84053 INH SWITCH ADDA ON X None 0 NO0 1 NO1 0 NO2 1 NO3 0 NO4 1 NO5 NOTE: Logic “0” ≤0.8V. Logic “1” ≥2.4V, with V+ between 2.7V and 10V Don’t Care. ...
Page 4
... V INH INL ADDH S I ADDL 4 ISL84051, ISL84052, ISL84053 Thermal Information Thermal Resistance (Typical, Note SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . 16 Ld SSOP Package . . . . . . . . . . . . . . . . . . . . . . . Maximum Junction Temperature (Plastic Package 150 Maximum Storage Temperature Range -65 Maximum Lead Temperature (Soldering 10s 300 (Lead Tips Only) Operating Conditions Temperature Range ISL8405XIX ...
Page 5
... Flatness is defined as the difference between maximum and minimum value of on-resistance over the specified analog signal range. 8. Leakage parameter is 100% tested at high temp, and guaranteed by correlation Between any two switches. 5 ISL84051, ISL84052, ISL84053 = ±4.5V to ±5.5V, GND = 0V, V Test Conditions: V SUPPLY Unless Otherwise Specified (Continued) TEST CONDITIONS = ± ...
Page 6
... Crosstalk, (Note 9) (ISL84052, ISL840533 only) POWER SUPPLY CHARACTERISTICS Power Supply Range Positive Supply Current 5.5V 0V, V Switch On or Off 6 ISL84051, ISL84052, ISL84053 Test Conditions +4.5V to +5.5V GND = 0V, V Unless Otherwise Specified TEST CONDITIONS = 1.0mA 3.5V, COM 0V, 4.5V ...
Page 7
... Crosstalk, (Note 9) (ISL84052, ISL84053 only) POWER SUPPLY CHARACTERISTICS Power Supply Range Positive Supply Current 3.6V 0V, V Switch On or Off 7 ISL84051, ISL84052, ISL84053 Test Conditions +3.0V to +3.6V GND = 0V, V Unless Otherwise Specified TEST CONDITIONS = 1.0mA 1.5V COM 0V, 3V ...
Page 8
... V 90% SWITCH OUTPUT 0V t OFF Logic input waveform is inverted for switches that have the opposite logic sense. FIGURE 1A. INHIBIT t /t MEASUREMENT POINTS ON OFF 8 ISL84051, ISL84052, ISL84053 LOGIC INPUT t < 20ns r t < 20ns f LOGIC OUT 90% INPUT LOGIC INPUT Repeat test for other switches. C capacitance ...
Page 9
... INPUT 0V t TRANS V VNOX SWITCH 0V OUTPUT 10% VNOX t TRANS Logic input waveform is inverted for switches that have the opposite logic sense. FIGURE 1C. ADDRESS t MEASUREMENT POINTS TRANS 9 ISL84051, ISL84052, ISL84053 (Continued LOGIC INPUT t < 20ns r t < 20ns OUT 90% LOGIC INPUT V- C LOGIC INPUT Repeat test for other switches ...
Page 10
... C OUT L FIGURE 2A. Q MEASUREMENT POINTS 3V LOGIC INPUT 0V SWITCH OUTPUT V OUT 0V t BBM FIGURE 3A. t MEASUREMENT POINTS BBM 10 ISL84051, ISL84052, ISL84053 (Continued) 3V OFF 0V V ∆V G OUT Repeat test for other switches. FIGURE 2. CHARGE INJECTION C V+ LOGIC INPUT t < 20ns r t < 20ns ...
Page 11
... R L FIGURE 4. OFF ISOLATION TEST CIRCUIT V+ C SIGNAL GENERATOR ISL84052/3 ADDX ANALYZER COM B GND R L FIGURE 6. CROSSTALK TEST CIRCUIT 11 ISL84051, ISL84052, ISL84053 (Continued ADDX INH V- C 50Ω COM A IMPEDANCE ANALYZER or NC N.C. B INH ...
Page 12
... Detailed Description The ISL84051, ISL84052, ISL84053 analog switches offer precise switching capability from a bipolar single 2V to 12V supply with low on-resistance (60Ω) and high speed operation (t = 50ns OFF are especially well suited to portable battery powered equipment thanks to the low operating supply voltage (2V), low power consumption (3µ ...
Page 13
... COM FIGURE 11. ON RESISTANCE vs SWITCH VOLTAGE 13 ISL84051, ISL84052, ISL84053 and the analog signal. This means their leakages will vary as the signal varies. The difference in the two diode leakages to the V+ and V- pins constitutes the analog-signal- path leakage current. All analog leakage current flows between each pin and one of the supply terminals, not to the other switch terminal ...
Page 14
... FIGURE 15. ADDRESS TRANS TIME vs SINGLE SUPPLY VOLTAGE = ± GAIN 0 ISL84051 -3 ISL84052 PHASE ISL84051 ISL84052 R = 50Ω FREQUENCY (MHz) FIGURE 17. FREQUENCY RESPONSE 14 ISL84051, ISL84052, ISL84053 Unless Otherwise Specified (Continued) A 200 COM 150 100 50 0 100 FIGURE 14 ...
Page 15
... Die Characteristics SUBSTRATE POTENTIAL (POWERED UP): GND TRANSISTOR COUNT: ISL84051: 193 ISL84052: 193 ISL84053: 193 PROCESS: Si Gate CMOS 15 ISL84051, ISL84052, ISL84053 ...
Page 16
... The lead width “B”, as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch) 10. Controlling dimension: MILLIMETER. Converted inch dimen- sions are not necessarily exact. 16 ISL84051, ISL84052, ISL84053 M16.15 (JEDEC MS-012-AC ISSUE C) 16 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE M M ...
Page 17
... However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 17 ISL84051, ISL84052, ISL84053 M16.15A 16 LEAD SHRINK NARROW BODY SMALL OUTLINE PLASTIC PACKAGE ...