EVAL-AD7660CB Analog Devices Inc, EVAL-AD7660CB Datasheet - Page 3

• Manufacturer Part Number: EVAL-AD7660CB
• Description: BOARD EVAL FOR AD7660
• Manufacturer: Analog Devices Inc
• Series: PulSAR®r

Specifications of EVAL-AD7660CB

• Rohs Status: RoHS non-compliant
• Number Of Adc's: 1
• Number Of Bits: 16
• Sampling Rate (per Second): 100k
• Data Interface: Serial, Parallel
• Inputs Per Adc: 1 Differential
• Input Range: ±VREF
• Power (typ) @ Conditions: 200mW @ 100kSPS
• Voltage Supply Source: Analog and Digital
• Operating Temperature: -40°C ~ 85°C
• Utilized Ic / Part: AD7660

Parameter
TEMPERATURE RANGE
NOTES
1
2
3
4
5
6
Specifications subject to change without notice.
TIMING SPECIFICATIONS
Parameter
REFER TO FIGURES 11 AND 12
REFER TO FIGURES 13, 14, AND 15 (Parallel Interface Modes)
REFER TO FIGURE 16 AND 17 (Master Serial Interface Modes)
REFER TO FIGURES 18 AND 20 (Slave Serial Interface Modes)
NOTES
1
2
Specifications subject to change without notice.
REV. D
LSB means least significant bit. With the 0 V to 2.5 V input range, one LSB is 38.15 mV.
Typical rms noise at worst-case transitions and temperatures.
See Definition of Specifications section. These specifications do not include the error contribution from the external reference.
All specifications in dB are referred to a full-scale input FS. Tested with an input signal at 0.5 dB below full-scale unless otherwise specified.
Tested in Parallel Reading Mode.
With all digital inputs forced to DVDD or DGND respectively.
In serial interface modes, the SYNC, SCLK, and SDOUT timings are defined with a maximum load C
If the polarity of SCLK is inverted, the timing references of SCLK are also inverted.
Specified Performance
Convert Pulsewidth
Time between Conversions
CNVST LOW to BUSY HIGH Delay
BUSY HIGH All Modes Except in
Aperture Delay
End of Conversion to BUSY LOW Delay
Conversion Time
Acquisition Time
RESET Pulsewidth
CNVST LOW to DATA Valid Delay
DATA Valid to BUSY LOW Delay
Bus Access Request to DATA Valid
Bus Relinquish Time
CS LOW to SYNC Valid Delay
CS LOW to Internal SCLK Valid Delay
CS LOW to SDOUT Delay
CNVST LOW to SYNC Delay
SYNC Asserted to SCLK First Edge Delay
Internal SCLK Period
Internal SCLK HIGH (INVSCLK Low)
Internal SCLK LOW (INVSCLK Low)
SDOUT Valid Setup Time
SDOUT Valid Hold Time
SCLK Last Edge to SYNC Delay
CS HIGH to SYNC HI-Z
CS HIGH to Internal SCLK HI-Z
CS HIGH to SDOUT HI-Z
BUSY HIGH in Master Serial Read after Convert
CNVST LOW to SYNC Asserted Delay
SYNC Deasserted to BUSY LOW Delay
External SCLK Setup Time
External SCLK Active Edge to SDOUT Delay
SDIN Setup Time
SDIN Hold Time
External SCLK Period
External SCLK HIGH
External SCLK LOW
Master Serial Read after Convert Mode
(–40 C to +85 C, AVDD = DVDD = 5 V, OVDD = 2.7 V to 5.25 V, unless otherwise noted.)
2
2
Conditions
T
MIN
to T
MAX
1
1
–3–
Symbol
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
Min
–40
L
of 10 pF; otherwise, the load is 60 pF maximum.
Min
5
10
10
8
10
45
5
4
40
30
9.5
4.5
3
3
5
3
5
5
25
10
10
Typ
Typ
2
500
1.5
50
Max
+85
Max
15
2
2
2
40
15
10
10
10
75
10
10
10
3.2
16
AD7660
Unit
∞C
Unit
ns
ms
ns
ms
ns
ns
ms
ms
ns
ms
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ms
ms
ns
ns
ns
ns
ns
ns
ns
ns