SI3402-EVB Silicon Laboratories Inc, SI3402-EVB Datasheet - Page 7

• Manufacturer Part Number: SI3402-EVB
• Description: BOARD EVAL POE FOR SI3402
• Manufacturer: Silicon Laboratories Inc
• Type: PWM Controllersr

Specifications of SI3402-EVB

• Main Purpose: Special Purpose DC/DC, Power Over Ethernet
• Outputs And Type: 1, Non-Isolated
• Voltage - Output: 5V
• Voltage - Input: 44 ~ 57V
• Regulator Topology: Buck
• Frequency - Switching: 350kHz
• Board Type: Fully Populated
• Utilized Ic / Part: Si3402
• Input Voltage: 5 V
• Output Voltage: 3.3 V
• Interface Type: Ethernet
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Product: Power Management Modules
• For Use With/related Products: Si3402
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Current - Output: -
• Power - Output: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1827

Table 5. Electrical Characteristics
Parameter
VPORT
Input Offset Current
Diode Bridge Leakage
IPORT Classification
IPORT Operating Current
Current Limit
Hotswap FET On-Resistance +
R
Power Loss VPORT Threshold
Switcher Frequency
Maximum Switcher Duty Cycle
Switching FET On-Resistance
Regulated Feedback @ Pin FB
Regulated Output Voltage Tolerance
Notes:
SENSE
1. Transient surge defined in IEC60060 as a 1000 V impulse of either polarity applied to CT1–CT2 or SP1–SP2. The
2. The classification currents are guaranteed only when recommended RCLASS resistors are used, as specified in
3. IPORT includes full operating current of switching regulator controller.
4. The PD interface includes dual-level input current limit. At turn-on, before the HSO load capacitor is charged, the
5. See “AN296: Using the Si3400/1/2 PoE PD Controller in Isolated and Non-Isolated Designs” for more information.
6. Applies to non-isolated applications only (VOUT on schematic in Figure 1).
shape of the impulse shall have a 300 ns full rise time and a 50 µs half fall time with 201  source impedance.
Table 11.
current limit is set at the inrush level. After the capacitor has been charged within ~1.25 V of VNEG, the operating
current limit is engaged. This higher current limit remains active until the UVLO lower limit has been tripped or until the
hotswap switch is sufficiently current-limited to cause a foldback of the HSO voltage.
4
2
3
5
6
6
Output voltage tolerance @
ISOSSFT connected to
36 V < VPORT < 57 V
36 V < VPORT < 57 V
Transient Surge
UVLO Turn Off
UVLO Turn On
VPORT < 10 V
VPORT = 57 V
Classification
Description
Operating
Detection
DC Avg.
Class 0
Class 1
Class 2
Class 3
Class 4
Inrush
VOUT
VDD
Rev. 1.2
1
Min
470
2.7
0.5
0.3
14
30
27
—
62
—
—
17
26
36
—
—
—
—
—
–5
0
9
1.23
Typ
350
140
30
50
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
2
Max
0.86
680
3.1
1.5
33
11
22
42
36
79
10
25
12
20
30
44
—
—
—
—
4
5
Si3402
Unit
kHz
mA
mA
µA
µA
mA
mA
%
%


V
V
V
7