HS2238RECB62H Renesas Electronics America, HS2238RECB62H Datasheet

Page 1

To our customers, Old Company Name in Catalogs and Other Documents st On April 1 , 2010, NEC Electronics Corporation merged with Renesas Technology Corporation, and Renesas Electronics Corporation took over all the business of both companies. Therefore, although the ...

Page 2

All information included in this document is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas Electronics products listed herein, please confirm ...

Page 3

... Throughout this document, the term "user system interface cable" shall be defined as the following product produced only by Renesas Technology Corp. excluding all subsidiary products. • User system interface cable (HS2238RECB62H) The user system or a host computer is not included in this definition. Purpose of the User System Interface Cable: This user system interface cable is for connecting the emulator station and user system ...

Page 4

LIMITED WARRANTY Renesas warrants its user system interface cables to be manufactured in accordance with published specifications and free from defects in material and/or workmanship. Renesas will repair or replace any user system interface cables determined to be defective in ...

Page 5

State Law: Some states do not allow the exclusion or limitation of implied warranties or liability for incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and ...

Page 6

READ this user's manual before using this user system interface cable. • KEEP the user's manual handy for future reference. Do not attempt to use the user system interface cable until you fully understand its mechanism. DEFINITION OF SIGNAL ...

Page 7

WARNING Observe the precautions listed below. Failure will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST ...

Page 8

... H8S/2238R Group BP-112 User System Interface Cable (HS2238RECB62H) for E6000 Emulator User’s Manual H8S/2238R E6000 HS2238RECB62HE H8S Family / H8S/2200 Series Rev.1.0 2003.06 ...

Page 9

Cautions Keep safety first in your circuit designs! 1. Renesas Technology Corporation puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may ...

Page 10

... Thank you for purchasing this user system interface cable (HS2238RECB62H) for the Renesas’s original microcomputer H8S/2238R group. The HS2238RECB62H is a user system interface cable that connects an H8S/2633 group E6000 emulator (HS2633REPI61H, HS2633EPI61H; hereinafter referred to as the emulator) to the IC socket for a BP-112 package for the H8S/2238R group MCU on the user system. ...

Page 11

Section 1 Configuration....................................................................................1 Section 2 Connection Procedures ......................................................................3 2.1 Connecting User System Interface Cable to Emulator Station ......................................... 3 2.2 Connecting User System Interface Cable to User System ................................................ 5 2.2.1 Soldering the IC Socket ....................................................................................... 5 2.2.2 Inserting Cable ...

Page 12

... Section 1 Configuration Use an CSPACK112A1110H02 socket (socket (manufactured by Tokyo Eletech Corporation) for the BP-112 package IC socket on the user system. Figure 1 shows the configuration of the HS2238RECB62H user system interface cable for the BP-112 package. Figure 1 HS2238RECB62H User System Interface Cable CAUTION 1 ...

Page 13

... Table 1 lists the HS2238RECB62H components. Please make sure you have all of these components when unpacking. Table 1 HS2238RECB62H Components No. Component 1 Cable body 2 Cable head 3 IC socket 4 Spacer 5 Cover 6 Screws (M1 mm) 7 Driver 8 Documentation 2 Quantity Remarks 1 Includes flat cable 1 1 For the BP-112 package ...

Page 14

Section 2 Connection Procedures 2.1 Connecting User System Interface Cable to Emulator Station Observe the precautions listed below. Failure will result in a FIRE HAZARD and will damage the user system and the emulator product or will ...

Page 15

Figure 2 Connecting User System Interface Cable to Emulator Station 4 ...

Page 16

Connecting User System Interface Cable to User System Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part. Before connecting, make sure that pin 1 ...

Page 17

Notes on soldering the IC socket a) The IC socket is larger than the actual IC package; therefore, refer to figure 7 for the installation of other components not install components that occupy large volume close to ...

Page 18

CAUTION 1. Never dip the IC socket in flux or use wash to clean the IC socket. This is because flux may remain inside the IC socket due to the IC socket’s structure. When using the IC socket with other ...

Page 19

Inserting Cable Head Check the location of pin 1 before inserting. Align pin 1 on the IC socket for an BP-112 package on the user system with pin 1 on the user system interface cable head, and insert the ...

Page 20

... If the emulator does not operate correctly, cracks might have occurred in the solder. The user system interface cable (HS2238RECB62H) head and the IC socket for the BP-112 package on the user system have no pin dedicated for alignment. Use the follow procedure to fasten the cable head ...

Page 21

Next, fasten screws to and should be tightened a little at a time, alternating between screws on opposing corners. Figure 5 Fastening Cable Head Procedure ( little, so that four screw holes are aligned. Then, each screw ...

Page 22

Fastening Cable Body Connect the cable body to the cable head. Figure 6 Fastening Cable Body 11 ...

Page 23

Recommended Dimensions for User System Mount Pad Figure 7 shows the recommended dimensions for the mount pad (footprint) for the user system with an IC socket for an BP-112 package (CSPACK112A1110H02: socket (manufactured by Tokyo Eletech Corporation). Note that ...

Page 24

Dimensions for User System Interface Cable Head The dimensions for the user system interface cable head are shown in figure 8. Figure 8 Dimensions for User System Interface Cable Head 13 ...

Page 25

Resulting Dimensions after Connecting User System Interface Cable The resulting dimensions, after connecting the user system interface cable head to the user system, are shown in figure 9. Figure 9 Resulting Dimensions after Connecting User System Interface Cable 14 ...

Page 26

Section 3 Installing the MCU to the User System CAUTION 1. Check the location of pin 1 before inserting. 2. Use a provided screwdriver. 3. The tightening torque must be 0.054 N•m or less. If the applied torque cannot be ...

Page 27

Figure 10 Installing MCU to User System 16 ...

Page 28

Section 4 Verifying Operation 1. When using the E6000 emulator for the H8S/2633 series, turn on the emulator according to the procedures described in the H8S/2633 E6000 Emulator User's Manual (HS2633REPI61HE). 2. Verify the user system interface cable connections by ...

Page 29

Make sure that pin 1 on the user system IC socket is correctly aligned with pin 1 on the cable head before inserting the cable head into the user system IC socket. 2. The dimensions of the recommended mount ...

Page 30

... H8S/2238R Group BP-112 User System Interface Cable (HS2238RECB62H) for E6000 Emulator User's Manual Publication Date: Rev.1.00, June 3, 2003 Published by: Sales Strategic Planning Div. Renesas Technology Corp. Edited by: Technical Documentation & Information Department Renesas Kodaira Semiconductor Co., Ltd. 2003 Renesas Technology Corp. All rights reserved. Printed in Japan. ...

Page 31

... H8S/2238R Group BP-112 User System Interface Cable (HS2238RECB62H) for E6000 Emulator User’s Manual H8S/2238R E6000 HS2238RECB62HE 1753, Shimonumabe, Nakahara-ku, Kawasaki-shi, Kanagawa 211-8668 Japan ...