HS2338ECH61H Renesas Electronics America, HS2338ECH61H Datasheet

Page 1

To our customers, Old Company Name in Catalogs and Other Documents st On April 1 , 2010, NEC Electronics Corporation merged with Renesas Technology Corporation, and Renesas Electronics Corporation took over all the business of both companies. Therefore, although the ...

Page 2

All information included in this document is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas Electronics products listed herein, please confirm ...

Page 3

... H8S/2338Series QFP-144 User System Interface Cable (HS2338ECH61H) for E6000 Emulator User’s Manual ...

Page 4

Renesas neither warrants nor grants licenses of any rights of Renesas’s or any third party’s patent, copyright, trademark, or other intellectual property rights for information contained in this document. Renesas bears no responsibility for problems that may arise with ...

Page 5

... Thank you for purchasing this user system interface cable (HS2338ECH61H) for the Renesas’s original microcomputer H8S/2338 series. The HS2338ECH61H is a user system interface cable that connects an H8S/2338 series E6000 emulator (HS2338EPI61H; hereinafter referred to as the emulator) to the IC socket for a QFP-144 package (package code: FP-144) for the H8S/2338 series MCU on the user system ...

Page 6

Section 1 Configuration...................................................................................1 Section 2 Connection Procedures ....................................................................4 2.1 Connecting User System Interface Cable to Emulator Station ......................................... 4 2.2 Connecting User System Interface Cable to User System ................................................ 5 2.2.1 Installing IC Socket ............................................................................................. 6 2.2.2 Inserting Cable Head ...

Page 7

... Section 1 Configuration Use an NQPACK144SD socket (manufactured by Tokyo Eletech Coporation) for the FP-144 package IC socket on the user system. Figure 1 shows the configuration of the HS2338ECH61H user system interface cable for the FP-144 package. CA UTION 1 ...

Page 8

... To emulator station Screws ( mm) Figure 1 HS2338ECH61H User System Interface Cable 2 Cable body Socket cover IC socket User system Screws ( mm) (for fastening cable head) Cable head ...

Page 9

... Table 1 lists the HS2338ECH61H components. Please make sure you have all of these components when unpacking. Table 1 HS2338ECH61H Components No. Component 1 Cable body 2 Cable head 3 IC socket 4 Socket cover 5 Screws ( mm) 6 Screws ( mm) 7 Guide pins (φ 1 mm) 8 Screwdriver 9 Documentation Quantity Remarks 1 Includes flat cable ...

Page 10

Section 2 Connection Procedures 2.1 Connecting User System Interface Cable to Emulator Station Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part. Before connecting, make ...

Page 11

Emulator station Figure 2 Connecting User System Interface Cable to Emulator Station 2.2 Connecting User System Interface Cable to User System Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to ...

Page 12

Installing IC Socket 1. Confirming the location of IC socket After confirming the location of pin 1 on the IC socket, apply epoxy resin adhesive to the end of the four projections at the bottom of the IC socket, ...

Page 13

Inserting Cable Head Check the location of pin 1 before inserting. Align pin 1 on the IC socket for a FP-144 system interface cable head into the IC socket on the user system, as shown in figure 4. 2.2.3 ...

Page 14

Fasten the user system interface cable head to the IC socket for an FP-144 package on the user system with the four screws (M2 time, alternating between screws on opposing corners. Take special care, such as manually securing the IC ...

Page 15

Connecting Cable Body to Cable Head Connect the cable body to the cable head. Cable body User system Figure 5 Remove jig Cable head Fastening Cable Body Removing Push the remove jig 9 ...

Page 16

Recommended Dimensions for User System Mount Pad Figure 6 shows the recommended dimensions for the mount pad (footprint) for the user system with an IC socket for an FP-144 package (NQPACK144SD: manufactured by Tokyo Eletech Corporation). Note that the ...

Page 17

Dimensions for User System Interface Cable Head The dimensions for the user system interface cable head are shown in figure 7. Figure 7 Dimensions for User System Interface Cable Head Unit: mm Tolerance: –0 ...

Page 18

Resulting Dimensions after Connecting User System Interface Cable The resulting dimensions, after connecting the user system interface cable head to the user system, are shown in figure 8. Cable head IC socket (NQPACK144SD User system manufactured by Tokyo Eletech ...

Page 19

Section 3 Installing the MCU to the User System 1. Check the location of pin 1 before inserting. 2. Use the screwdriver provided for tightening screws. 3. The tightening torque must be 0.054 N•m or less. If the applied torque ...

Page 20

Figure 9 14 Screws ( mm) Pin 1 IC socket (NQPACK144SD manufactured by Tokyo Eleteck Corporation) User system Installing MCU to User System Socket cover MCU ...

Page 21

Section 4 Verifying Operation 1. When using the E6000 emulator for the H8S/2338 series, turn on the emulator according to the procedures described in the E6000 Series Emulator User's Manual (HS2000EPI61HE). 2. Verify the user system interface cable connections by ...

Page 22

In the H8S/2338 series MCU, the interrupt signal pins can be selected by the register setting. To trace the interrupt signals in the E6000 emulator, select the interrupt signal pins by setting switch P5 on the user system interface ...

Page 23

Make sure that pin 1 on the user system IC socket is correctly aligned with pin 1 on the cable head before inserting the cable head into the user system IC socket. 2. The dimensions of the recommended mount ...