AXA010A0X3Z Lineage Power, AXA010A0X3Z Datasheet - Page 12

• Manufacturer Part Number: AXA010A0X3Z
• Description: CONVER DC/DC 0.75 5.5V @ 10A SIP
• Manufacturer: Lineage Power
• Series: Austin Lynx™r
• Type: Point of Load (POL) Non-Isolated with Remote On/Offr

Specifications of AXA010A0X3Z

• Output: 0.75 ~ 5.5V
• Number Of Outputs: 1
• Power (watts): 55W
• Mounting Type: Through Hole
• Voltage - Input: 10 ~ 14V
• Package / Case: 10-SIP Module
• 1st Output: 0.75 ~ 5.5 VDC @ 10A
• Size / Dimension: 2.00" L x 0.32" W x 0.50" H (50.8mm x 8.1mm x 12.7mm)
• Power (watts) - Rated: 55W
• Operating Temperature: -40°C ~ 85°C
• Efficiency: 93%
• Approvals: CSA, EN, UL, VDE
• Output Current: 10A
• Input Voltage: 12V
• Output Voltage: 0.75 to 5.5V
• Screening Level: Industrial
• Product Length (mm): 50.8mm
• Product Height (mm): 12.7mm
• Product Depth (mm): 8.1mm
• Mounting Style: Through Hole
• Pin Count: 10
• Output Power: 55 W
• Input Voltage Range: 10 V to 14 V
• Output Voltage (channel 1): 0.75 V to 5.5 V
• Output Current (channel 1): 10 A
• Package / Case Size: SIP
• Output Type: Non-Isolated
• Product: Non-Isolated / POL
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• 3rd Output: -
• 2nd Output: -
• Lead Free Status / Rohs Status: Compliant
• Other names: 555-1062; CC109101318

Data Sheet
September 30, 2009
Feature Description
Remote On/Off
The 12V Austin Lynx Programmable SIP power
modules feature an On/Off pin for remote On/Off
operation. If not using the remote On/Off pin, leave the
pin open (module will be On). The On/Off pin signal
(Von/Off) is referenced to ground. To switch the module
on and off using remote On/Off, connect an open
collector npn transistor between the On/Off pin and the
ground pin (See Figure 27).
During a logic-high (On/Off pin is pulled high internal to
the module) when the transistor is in the Off state, the
power module is ON. The maximum allowable leakage
current of the transistor when Von/off = V
During a logic-low when the transistor is turned-on, the
power module is OFF. During this state VOn/Off is less
than 0.3V and the maximum IOn/Off = 1mA.
Figure 27. Circuit configuration for using positive
logic On/OFF.
Overcurrent Protection
To provide protection in a fault (output overload)
condition, the unit is equipped with internal
current-limiting circuitry and can endure current limiting
continuously. At the point of current-limit inception, the
unit enters hiccup mode. The unit operates normally
once the output current is brought back into its specified
range. The typical average output current during hiccup
is 3A.
Input Undervoltage Lockout
At input voltages below the input undervoltage lockout
limit, module operation is disabled. The module will
begin to operate at an input voltage above the
undervoltage lockout turn-on threshold.
LINEAGE
I
ON/OFF
GND
VIN+
ON/OFF
POWER
V
Q1
ON/OFF
+
_
R1
12V Austin Lynx
10Vdc – 14Vdc input; 0.75Vdc to 5.5Vdc Output;10A Output Current
R2
R3
R4
Q2
IN,max
MODULE
PWM Enable
Q3
is 10µA.
TM
CSS
SIP Non-isolated Power Modules, Programmable:
Overtemperature Protection
equipped with a thermal shutdown circuit. The unit will
shutdown if the thermal reference point T
125
intended as a guarantee that the unit will survive
temperatures beyond its rating. The module will
automatically restarts after it cools down.
To provide protection in a fault condition, the unit is
o
C (typical), but the thermal shutdown is not
ref
, exceeds
12