AXA016A0X3-SRZ Lineage Power, AXA016A0X3-SRZ Datasheet - Page 10

• Manufacturer Part Number: AXA016A0X3-SRZ
• Description: CONVER DC/DC 0.75 5.5V @ 16A SMD
• Manufacturer: Lineage Power
• Series: Austin SuperLynx™r
• Type: Point of Load (POL) Non-Isolated with Remote On/Offr

Specifications of AXA016A0X3-SRZ

• Output: 0.75 ~ 5.5V
• Number Of Outputs: 1
• Power (watts): 88W
• Mounting Type: Surface Mount
• Voltage - Input: 10 ~ 14V
• Package / Case: 6-SMD Module
• 1st Output: 0.75 ~ 5.5 VDC @ 16A
• Size / Dimension: 1.30" L x 0.53" W x 0.33" H (33mm x 13.5mm x 8.3mm)
• Power (watts) - Rated: 88W
• Operating Temperature: -40°C ~ 85°C
• Efficiency: 92%
• Approvals: CSA, EN, UL, VDE
• Output Power: 88 W
• Input Voltage Range: 10 V to 14 V
• Output Voltage (channel 1): 0.75 V to 5.5 V
• Output Current (channel 1): 16 A
• Package / Case Size: SMD
• Output Type: Non-Isolated
• Output Voltage: 0.75 V to 5.5 V
• Product: Non-Isolated / POL
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• 3rd Output: -
• 2nd Output: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 555-1065-2; CC109104840

Data Sheet
October 1, 2009
Test Configurations
Figure 23. Input Reflected Ripple Current Test Setup.
Figure 24. Output Ripple and Noise Test Setup.
Figure 25. Output Voltage and Efficiency Test Setup.
LINEAGE
NOTE: All voltage measurements to be taken at the module
V
COM
O
(+)
terminals, as shown above. If sockets are used then
Kelvin connections are required at the module terminals
to avoid measurement errors due to socket contact
resistance.
Efficiency
TO OSCILLOSCOPE
NOTE: Measure input reflected ripple current with a simulated
R
R
NOTE: All voltage measurements to be taken at the module
distribution
distribution
POWER
source inductance (L
possible battery impedance. Measure current as shown
above.
COPPER STRIP
1uF .
terminals, as shown above. If sockets are used then
Kelvin connections are required at the module terminals
to avoid measurement errors due to socket contact
resistance.
R
R
contact
contact
η =
@ 20°C 100kHz
E.S.R.<0.1Ω
C
Electrolytic
S
GROUND PLANE
1000μF
L
1μH
TEST
V
10uF
IN
V
V
V
COM
TEST
IN
IN
O
(+)
. I
. I
) of 1μH. Capacitor C
O
IN
SCOPE
COM
V
O
Tantalum
2x100μF
C
V
10 – 14Vdc input; 0.75Vdc to 5.5Vdc Output; 16A output current
x 100 %
IN
O
RESISTIVE
LOAD
CURRENT PROBE
Austin SuperLynx
R
R
S
contact
contact
offsets
V
COM
IN
(+)
R
R
distribution
distribution
R
LOAD
Design Considerations
Input Filtering
The Austin SuperLynx
connected to a low-impedance source. A highly inductive
source can affect the stability of the module. An input
capacitance must be placed directly adjacent to the input
pin of the module, to minimize input ripple voltage and
ensure module stability.
In a typical application, 6x47 µF low-ESR tantalum
capacitors (AVX part #: TPSE476M025R0100, 47µF 25V
100 mΩ ESR tantalum capacitor) will be sufficient to
provide adequate ripple voltage at the input of the
module. To further minimize ripple voltage at the input,
very low ESR ceramic capacitors are recommended at
the input of the module. Figure 26 shows input ripple
voltage (mVp-p) for various outputs with 6x47 µF
tantalum capacitors and with 6x22 µF ceramic capacitor
(TDK part #: C4532X5R1C226M) at full load.
Figure 26. Input ripple voltage for various output
with 6x47 µF tantalum capacitors and with 6x22 µF
ceramic capacitors at the input (full load).
TM
12V SMT Non-isolated Power Modules:
300
200
350
250
100
150
50
0
0
1
TM
Output Voltage (Vdc)
12V SMT module should be
2
3
4
.
Tantalum
Ceramic
5
10
6