MW005AJ Lineage Power, MW005AJ Datasheet - Page 12

• Manufacturer Part Number: MW005AJ
• Description: CONVERTER DC/DC +-5V 5W OUT
• Manufacturer: Lineage Power
• Series: MW005r
• Type: Isolatedr

Specifications of MW005AJ

• Output: ±5V
• Number Of Outputs: 2
• Power (watts): 5W
• Mounting Type: Through Hole
• Voltage - Input: 36 ~ 72V
• Package / Case: 5-DIP Module
• 1st Output: 5 VDC @ 500mA
• 2nd Output: -5 VDC @ 500mA
• Size / Dimension: 2.00" L x 1.10" W x 0.46" H (50.8mm x 27.9mm x 11.7mm)
• Power (watts) - Rated: 5W
• Operating Temperature: -40°C ~ 85°C
• Approvals: CE, CSA, UL, VDE
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• 3rd Output: -
• 4th Output: -

MW005-Series Power Modules:
36 Vdc to 75 Vdc Inputs; 5 W
Test Configurations
Note: Use a 0.1 µF ceramic capacitor. Scope measurement should
Figure 25. MW005-Series Peak-to-Peak Output
Note: All measurements are taken at the module terminals. When
Figure 26. MW005A, B, C Output Voltage and
12
12
CONTACT RESISTANCE
V
V
SUPPLY
be made using a BNC socket. Position the load between
50 mm and 75 mm (2 in. and 3 in.) from the module.
socketing, place Kelvin connections at module terminals to
avoid measurement errors due to socket contact resistance.
O
O
(+)
(–)
=
Noise Measurement Test Setup
Efficiency Measurement Test Setup
------------------------------------------------------ -
V
I
V
I
O
I
COPPER STRIP
+
+
–
–
V
V
V
V
I
I
(–)
O
(+)
I
0.1 µF
–
–
V
V
(continued)
O
I
O
I
I
(+)
(–)
O
SCOPE
100
DISTRIBUTION LOSSES
I
O
CONTACT AND
%
RESISTIVE
LOAD
LOAD
8-513(C)
8-204(C)
Note: All measurements are taken at the module terminals. When
Figure 27. MW005BK, CL Output Voltage and
Design Considerations
Input Reflected Ripple
An internal aluminum electrolytic input capacitor is
used for filtering; therefore, input ripple increases as
temperature decreases. There is approximately two
times more ripple at 0 °C than at 25 °C and eight times
more ripple at –40 °C than at 25 °C. The power module
functions properly down to –40 °C with no additional
filtering. If lower ripple comparable to that at 25 °C is
needed at low temperatures, an external capacitor
across the input with an impedance of 0.5
over the desired temperature range is recommended.
See Figure 24 for the test setup.
Input or Output Voltage Reversal
CAUTION: Applying a reverse voltage across the
SUPPLY
socketing, place Kelvin connections at module terminals to
avoid measurement errors due to socket contact resistance.
=
RESISTANCE
CONTACT
J
--------------------------------------------------------------------------
Efficiency Measurement Test Setup
module input or output can damage the
module.
2
1
I
I
V
V
I
OJ
+
+
–
V
V
V
I
I
(+)
(–)
–
I
V
–
COM
I
COM
I
V
V
Tyco Electronics Corp.
O1
O2
I
OJ
DISTRIBUTION LOSSES
CONTACT AND
100
Data Sheet
April 1999
at 100 kHz
%
LOAD
LOAD
8-506(C)