FW250F1 Lineage Power, FW250F1 Datasheet - Page 10

• Manufacturer Part Number: FW250F1
• Description: CONVERTER DC/DC 3.3V 165W OUT
• Manufacturer: Lineage Power
• Series: FW250r
• Type: Isolated with Remote On/Offr

Specifications of FW250F1

• Output: 3.3V
• Number Of Outputs: 1
• Power (watts): 165W
• Mounting Type: Through Hole
• Voltage - Input: 36 ~ 75V
• Package / Case: Module
• 1st Output: 3.3 VDC @ 50A
• Size / Dimension: 4.60" L x 2.40" W x 0.53" H (116.8mm x 61mm x 13.5mm)
• Power (watts) - Rated: 165W
• Operating Temperature: -40°C ~ 100°C
• Efficiency: 79%
• Approvals: CE, CSA, UL, VDE
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• 3rd Output: -
• 2nd Output: -
• 4th Output: -

dc-dc Converters; 36 to 75 Vdc Input, 3.3 Vdc Output; 165 W to 198 W
Safety Considerations
For safety-agency approval of the system in which the
power module is used, the power module must be
installed in compliance with the spacing and separation
requirements of the end-use safety agency standard,
i.e., UL 1950, CSA C22.2 No. 950-95, and VDE 0805
(IEC60950, 3
If the input source is non-SELV (ELV or a hazardous
voltage greater than 60 Vdc and less than or equal to
75 Vdc), for the module’s output to be considered
meeting the requirements of safety extra-low voltage
(SELV), all of the following must be true:
Note: Do not ground either of the input pins of the
The power module has extra-low voltage (ELV) outputs
when all inputs are ELV.
The input to these units is to be provided with a maxi-
mum 20 A normal-blow fuse in the ungrounded lead.
10
10
The input source is to be provided with reinforced
insulation from any hazardous voltages, including the
ac mains; and
One V
both the input and output pins are to be kept floating;
and
The input pins of the module are not operator acces-
sible; and
Another SELV reliability test is conducted on the
whole system, as required by the safety agencies, on
the combination of supply source and the subject
module to verify that under a single fault, hazardous
voltages do not appear at the module’s output.
module without grounding one of the output pins.
This may allow a non-SELV voltage to appear
between the output pin and ground.
I
pin and one V
rd
edition).
O
pin are to be grounded or
Feature Descriptions
Overcurrent Protection
To provide protection in a fault (output overload) condi-
tion, the unit is equipped with internal current-limiting
circuitry and can endure current limiting for an unlim-
ited duration. At the point of current-limit inception, the
unit shifts from voltage control to current control. If the
output voltage is pulled very low during a severe fault,
the current-limit circuit can exhibit either foldback or
tailout characteristics (output-current decrease or
increase). The unit operates normally once the output
current is brought back into its specified range.
Remote On/Off
To turn the power module on and off, the user must
supply a switch to control the voltage between the on/off
terminal and the V
an open collector or equivalent (see Figure 17). A logic
low is V
The maximum I
should maintain a logic-low voltage while sinking 1 mA.
During a logic high, the maximum V
the power module is 15 V. The maximum allowable
leakage current of the switch at V
If not using the remote on/off feature, short the
ON/OFF pin to V
Figure 17. Remote On/Off Implementation
on/off
I
V
on/off
on/off
+
–
= 0 V to 1.2 V, during which the module is on.
on/off
I
I
(–).
(–) terminal (V
during a logic low is 1 mA. The switch
CASE
ON/OFF
V
V
I
I
(+)
(–)
SENSE(–)
SENSE(+)
on/off
Tyco Electronics Corp..
on/off
V
V
). The switch can be
on/off
O
O
(+)
(–)
= 15 V is 50 µA.
generated by
July 2002
8-580