6N139S-TA1 Lite-On Electronics, 6N139S-TA1 Datasheet - Page 11

• Manufacturer Part Number: 6N139S-TA1
• Description: OPTOCOUPLER DARL OUT 8-SMD
• Manufacturer: Lite-On Electronics

Specifications of 6N139S-TA1

• Input Type: DC
• Package / Case: 8-SMD
• Voltage - Isolation: 5000Vrms
• Number Of Channels: 1, Unidirectional
• Current - Output / Channel: 60mA
• Propagation Delay High - Low @ If: 1.6µs @ 1.6mA
• Current - Dc Forward (if): 20mA
• Output Type: Logic
• Mounting Type: Surface Mount
• Voltage - Output: 18V
• Current Transfer Ratio (min): 500% @ 1.6mA
• Isolation Voltage: 5000 Vrms
• Maximum Fall Time: 25 us
• Maximum Rise Time: 60 us
• Output Device: Photodarlington
• Configuration: 1 Channel
• Current Transfer Ratio: 1600 %
• Maximum Baud Rate: 100 KBps
• Maximum Forward Diode Voltage: 1.7 V
• Maximum Reverse Diode Voltage: 5 V
• Maximum Input Diode Current: 20 mA
• Maximum Power Dissipation: 35 mW
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Vce Saturation (max): -
• Current Transfer Ratio (max): -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 160-1802-2

BNS-OD-C131/A4
Part No. : 6N138 / 6N139 series
*All Typical at T
Notes,
1. AC For 1 Minute, R.H. = 40 ~ 60%. Isolation voltage shall be measured using the following method.
(1) Short between anode and cathode on the primary side and between collector and emitter on the secondary
side.
(2) The isolation voltage tester with zero-cross circuit shall be used.
(3) The waveform of applied voltage shall be a sine wave.
2. For 10 Seconds
3. Current Transfer Ratio (CTR) is defined as the ration of output collector current, Io, to the forward LED
input current, IF, times 100%.
4. Pin 7 open.
5. Instantaneous common mode rejection voltage "output (1)" represents a common mode voltage variation that can
hold the output above (1) level (Vo>2.0V).Instantaneous common mode rejection voltage "output (0)" represents a
common mode voltage variation that can hold the output above (0) level (Vo<0.8V).
6. Device considered a two terminal device. Pins 1, 2, 3 and 4 shorted together and Pins 5, 6, 7 and 8 shorted together.
Input-Output Insulation
Leakage Current
Withstand Insulation
Test Voltage
Input-Output Resistance
Isolation Characteristics
Parameter
A
=25 C
L IT E - O N T E CH NO L O G Y CO RP O RAT IO N
45% RH, t = 5s,
V
RH ≤ 50%, t = 1min,
T
V
A
I-O
I-O
= 25
= 3kV DC, T
= 500V DC
Test Condition
o
C
Property of Lite-on Only
A
= 25
o
C
Symbol
V
R
I
I-O
ISO
I-O
5000
Min
10
Typ
12
Page : 11 of 15
Max
1.0
Units
V
µA
RMS