HCPL-3140#500 Avago Technologies US Inc., HCPL-3140#500 Datasheet - Page 7

• Manufacturer Part Number: HCPL-3140#500
• Description: OPTOCOUPLER 1CH 0.4A 8-SMD
• Manufacturer: Avago Technologies US Inc.

Specifications of HCPL-3140#500

• Package / Case: 8-SMD Gull Wing
• Voltage - Isolation: 3750Vrms
• Number Of Channels: 1, Unidirectional
• Current - Output / Channel: 600mA
• Propagation Delay High - Low @ If: 300ns @ 8mA
• Current - Dc Forward (if): 25mA
• Input Type: DC
• Output Type: Push-Pull, Totem-Pole
• Mounting Type: Surface Mount, Gull Wing
• Isolation Voltage: 3750 Vrms
• Maximum Fall Time: 50 ns
• Maximum Forward Diode Current: 25 mA
• Maximum Rise Time: 50 ns
• Minimum Forward Diode Voltage: 1.2 V
• Output Device: Logic Gate Photo IC
• Configuration: 1 Channel
• Maximum Forward Diode Voltage: 1.8 V
• Maximum Reverse Diode Voltage: 5 V
• Maximum Power Dissipation: 250 mW
• Maximum Operating Temperature: + 100 C
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Switching Specifications (AC)
Over recommended operating conditions unless otherwise specified.
Notes:
1. Derate linearly above 70 C free air temperature at a rate of 0.3 mA/ C.
2. Maximum pulse width = 10 s, maximum duty cycle = 0.2%. This value is intended to allow for component tolerances for designs with I
3. Derate linearly above 85 C, free air temperature at the rate of 4.0 mW/ C.
4. Input power dissipation does not require derating.
5. Maximum pulse width = 50 s, maximum duty cycle = 0.5%.
6. In this test, V
7. Maximum pulse width = 1 ms, maximum duty cycle = 20%.
8. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage 4500 V
9. Device considered a two-terminal device: pins on input side shorted together and pins on output side shorted together.
10. PDD is the difference between t
11. Common mode transient immunity in the high state is the maximum tolerable |dVcm/dt| of the common mode pulse V
12. Common mode transient immunity in a low state is the maximum tolerable |dV
13. This load condition approximates the gate load of a 1200 V/25 A IGBT.
14. The power supply current increases when operating frequency and Qg of the driven IGBT increases.
7
Package Characteristics
Parameter
Propagation Delay Time to
High Output Level
Propagation Delay Time to
Low Output Level
Propagation Delay
Difference Between Any
Two Parts or Channels
Rise Time
Fall Time
Output High Level Common
Mode Transient Immunity
Output Low Level Common
Mode Transient Immunity
Parameter
Input-Output Momentary
Withstand Voltage
Input-Output Resistance
Input-Output Capacitance
minimum = 0.4 A. See Application section for additional details on limiting I
current limit I
60747-5-2 Insulation Characteristics Table, if applicable.
will remain in the high state (i.e. Vo > 6.0 V).
will remain in a low state (i.e. Vo < 1.0 V).
OH
I-O
is measured with a DC load current. When driving capacitive load V
5 A). This test is performed before 100% production test for partial discharge (method B) shown in the IEC/EN/DIN EN
PHL
and t
Symbol
V
R
C
Symbol
t
t
PDD
t
t
|CM
|CM
PLH
PHL
R
F
ISO
I-O
I-O
PLH
H
L
between any two parts or channels under the same test conditions.
|
|
Min.
0.1
0.1
-0.5
25
25
Min.
3750
Typ.
0.2
0.3
50
50
35
35
Typ.
10
0.6
12
OL
peak.
CM
Max.
0.7
0.7
0.5
Max.
/dt| of the common mode pulse, V
OH
will approach V
Units
V
pF
Units
ns
ns
kV/ s
kV/ s
s
s
s
rms
CC
Test
Conditions
Rg = 47 ,
Cg = 3 nF,
f = 10 kHz,
Duty Cycle =
50%,
I
V
T
V
Test
Conditions
T
RH<50% for
V
Freq=1 MHz
F =
as I
CC
A
CM
A
I-O
=25 C,
= 25 C,
8 mA,
rms
= 30 V
=500 V
OH
= 1 kV
approaches zero amps.
for 1 second (leakage detection
CM
CM
, to assure that the output
to assure that the output
Fig.
Fig.
10,11,
12,13,
14,17
18
18
O
Note
8,9
9
peak
Note
14
10
11
12