HCPL-314J-000E Avago Technologies US Inc., HCPL-314J-000E Datasheet - Page 10

• Manufacturer Part Number: HCPL-314J-000E
• Description: OPTOCOUPLER GATE DRV 0.4A 16SOIC
• Manufacturer: Avago Technologies US Inc.

Specifications of HCPL-314J-000E

• Package / Case: 16-SOIC (0.300", 7.50mm Width)
• Voltage - Isolation: 3750Vrms
• Number Of Channels: 2, Unidirectional
• Propagation Delay High - Low @ If: 300ns @ 8mA
• Current - Dc Forward (if): 25mA
• Input Type: DC
• Output Type: Open Collector
• Mounting Type: Surface Mount
• Isolation Voltage: 3750 Vrms
• Maximum Fall Time: 0.05 us
• Maximum Forward Diode Current: 25 mA
• Minimum Forward Diode Voltage: 1.2 V
• Output Device: Logic Gate Photo IC
• Configuration: 2 Channel
• Maximum Forward Diode Voltage: 1.8 V
• Maximum Reverse Diode Voltage: 3 V
• Maximum Power Dissipation: 260 mW
• Maximum Operating Temperature: + 100 C
• Minimum Operating Temperature: - 40 C
• No. Of Channels: 2
• Optocoupler Output Type: Gate Drive
• Input Current: 12mA
• Output Voltage: 30V
• Opto Case Style: SOIC
• No. Of Pins: 16
• Common Mode Ratio: 10 KV/uS
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 516-1477-5

Applications Information
Eliminating Negative IGBT Gate Drive
To keep the IGBT firmly off, the HCPL-314J has a very low
maximum V
the lead inductance from the HCPL-314J to the IGBT gate
and emitter (possibly by mounting the HCPL-314J on a
small PC board directly above the IGBT) can eliminate
the need for negative IGBT gate drive in many applica-
tions as shown in Figure 19. Care should be taken with
such a PC board design to avoid routing the IGBT collec-
tor or emitter traces close to the HCPL-314J input as this
can result in unwanted coupling of transient signals into
10
Figure 19. Recommended LED Drive and Application Circuit for HCPL-314J.
CONTROL
INPUT
74XX
OPEN
COLLECTOR
CONTROL
INPUT
74XX
OPEN
COLLECTOR
+5 V
+5 V
270 Ω
OL
270 Ω
GND 1
GND 1
specification of 1.0 V. Minimizing Rg and
1
2
3
6
7
8
HCPL-314J
16
15
14
11
10
9
0.1 μF
0.1 μF
the input of HCPL-314J and degrade performance. (If the
IGBT drain must be routed near the HCPL-314J input,
then the LED should be reverse biased when in the off
state, to prevent the transient signals coupled from the
IGBT drain from turning on the HCPL-314J.) An external
clamp diode may be connected between pins 14 & 15
and pins 9 & 10 (as shown in Figure 19) for the protec-
tion of HCPL-314J in the case of IGBTs switching induc-
tive load.
+
–
+
–
FLOATING
SUPPLY
V
V
CC
CC
Rg
Rg
= 18 V
= 18 V
V
OL
3-PHASE
+ HVDC
- HVDC
AC