ADUM7440ARQZ Analog Devices Inc, ADUM7440ARQZ Datasheet - Page 14

• Manufacturer Part Number: ADUM7440ARQZ
• Description: IC ISOLATOR DGTL QUAD 16QSOP
• Manufacturer: Analog Devices Inc
• Series: iCoupler®r

Specifications of ADUM7440ARQZ

• Propagation Delay: 75ns
• Inputs - Side 1/side 2: 4/0
• Number Of Channels: 4
• Isolation Rating: 1000Vrms
• Voltage - Supply: 3 V ~ 5.5 V
• Data Rate: 1Mbps
• Output Type: Logic
• Package / Case: 16-QSOP
• Operating Temperature: -40°C ~ 105°C
• No. Of Channels: 4
• Supply Current: 4.3mA
• Supply Voltage Range: 3V To 5.5V
• Digital Ic Case Style: QSOP
• No. Of Pins: 16
• Operating Temperature Range: -40°C To +105°C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

ADuM7440/ADuM7441/ADuM7442
APPLICATIONS INFORMATION
PC BOARD LAYOUT
The ADuM744x digital isolators require no external interface
circuitry for the logic interfaces. Power supply bypassing is
strongly recommended at the input and output supply pins
(see Figure 16). A total of four bypass capacitors should be
connected between Pin 1 and Pin 2 for V
and Pin 8 for V
between Pin 15 and Pin 16 for V
V
Pin 10 and V
capacitor values should be between 0.01 µF and 0.1 µF. The
total lead length between both ends of the capacitor and the
power supply pin should not exceed 20 mm.
In applications involving high common-mode transients, it
is important to minimize board coupling across the isolation
barrier. Furthermore, users should design the board layout
so that any coupling that does occur equally affects all pins
on a given component side. Failure to ensure this can cause
voltage differentials between pins exceeding the absolute
maximum ratings of the device, thereby leading to latch-up
or permanent damage.
PROPAGATION DELAY-RELATED PARAMETERS
Propagation delay is a parameter that describes the time it takes
a logic signal to propagate through a component. The input-to-
output propagation delay time for a high-to-low transition may
differ from the propagation delay time of a low-to-high
transition.
Pulse width distortion is the maximum difference between
these two propagation delay values and an indication of how
accurately the timing of the input signal is preserved.
INPUT (V
OUTPUT (V
DD1B
Pin 7 should be connected together and supply V
V
V
Ix
V
IC/
ID/
V
GND
GND
)
DD1A
DD1B
Ox
Figure 16. Recommended Printed Circuit Board Layout
V
V
V
V
OC
OD
)
IA
IB
1
1
DD2A
Figure 17. Propagation Delay Parameters
DD1B
Pin 16 should be connected together. The
, between Pin 9 and Pin 10 for V
t
PLH
DD2A
t
PHL
. Supply V
DD1A
, between Pin 7
50%
DD1A
50%
V
GND
V
V
V
V
V
GND
DD2A
OA
OB
OC/
OD/
DD2B
Pin 1 and
DD2B
2
V
V
2
IC
ID
DD2B
, and
Rev. B | Page 14 of 20
Channel-to-channel matching refers to the maximum amount
the propagation delay differs between channels within a single
ADuM744x component.
Propagation delay skew refers to the maximum amount the
propagation delay differs between multiple ADuM744x
components operating under the same conditions.
DC CORRECTNESS AND MAGNETIC FIELD IMMUNITY
Positive and negative logic transitions at the isolator input
cause narrow (~1 ns) pulses to be sent to the decoder using the
transformer. The decoder is bistable and is, therefore, either set
or reset by the pulses, indicating input logic transitions. In the
absence of logic transitions at the input for more than ~1 µs, a
periodic set of refresh pulses indicative of the correct input state
is sent to ensure dc correctness at the output. If the decoder
receives no internal pulses of more than approximately 5 µs,
the input side is assumed to be unpowered or nonfunctional,
in which case the isolator output is forced to a default high state
by the watchdog timer circuit.
The magnetic field immunity of the ADuM744x is determined
by the changing magnetic field, which induces a voltage in the
transformer’s receiving coil large enough to either falsely set or
reset the decoder. The following analysis defines the conditions
under which this can occur. The 3 V operating condition of the
ADuM744x is examined because it represents the most suscep-
tible mode of operation.
The pulses at the transformer output have an amplitude greater
than 1.0 V. The decoder has a sensing threshold at about 0.5 V, thus
establishing a 0.5 V margin in which induced voltages can be
tolerated. The voltage induced across the receiving coil is given by
where:
β is magnetic flux density (gauss).
r
N is the number of turns in the receiving coil.
Given the geometry of the receiving coil in the ADuM744x and
an imposed requirement that the induced voltage be, at most,
50% of the 0.5 V margin at the decoder, a maximum allowable
magnetic field at a given frequency can be calculated. The result
is shown in Figure 18.
n
is the radius of the n
V = (−dβ / dt) ∑ π r
th
n
turn in the receiving coil (cm).
2
; n = 1, 2, … , N