LTC3704EMS Linear Technology, LTC3704EMS Datasheet - Page 9

• Manufacturer Part Number: LTC3704EMS
• Description: IC INV SYNC 5.2V 50MA 10MSOP
• Manufacturer: Linear Technology
• Type: Invertingr

Specifications of LTC3704EMS

• Internal Switch(s): No
• Synchronous Rectifier: No
• Number Of Outputs: 1
• Voltage - Output: -5.2V
• Current - Output: 50mA
• Frequency - Switching: 50kHz ~ 1MHz
• Voltage - Input: 2.5 ~ 36 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 10-MSOP, Micro10™, 10-uMAX, 10-uSOP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Power - Output: -

OPERATIO
minimum on-time (about 175ns). Below this output
current level, the converter will begin to skip cycles in
order to maintain output regulation. Figures 3 and 4 show
the light load switching waveforms for Burst Mode and
Pulse-Skip Mode operation for the converter in Figure 1.
Burst Mode Operation
Burst Mode operation is selected by leaving the MODE/
SYNC pin unconnected or by connecting it to ground. In
normal operation, the range on the I
to no load to full load is 0.30V to 1.2V. In Burst Mode
operation, if the error amplifier EA drives the I
below 0.525V, the buffered I
parator C1 will be clamped at 0.525V (which corresponds
to 25% of maximum load current). The inductor current
peak is then held at approximately 30mV divided by the
power MOSFET R
the Burst Mode comparator B1 will turn off the power
MOSFET and scale back the quiescent current of the IC to
250μA (sleep mode). In this condition, the load current will
be supplied by the output capacitor until the I
rises above the 50mV hysteresis of the burst comparator.
At light loads, short bursts of switching (where the aver-
age inductor current is 25% of its maximum value) fol-
lowed by long periods of sleep will be observed, thereby
greatly improving converter efficiency. Oscilloscope wave-
forms illustrating Burst Mode operation are shown in
Figure 3.
Pulse-Skip Mode Operation
With the MODE/SYNC pin tied to a DC voltage above 1.2V,
Burst Mode operation is disabled. The internal, 0.525V
50mV/DIV
5A/DIV
V
OUT
I
L
Figure 3. LTC3704 Burst Mode Operation
(MODE/SYNC = 0V) at Low Output Current
DS(ON)
U
. If the I
10μs/DIV
TH
MODE/SYNC = 0V
(Burst Mode OPERATION)
TH
input to the current com-
pin drops below 0.30V,
TH
pin corresponding
3704 F03
TH
TH
voltage
voltage
buffered I
to directly control the current comparator from no load to
full load. With no load, the I
the power MOSFET is turned off and sleep mode is
invoked. Oscilloscope waveforms illustrating this mode of
operation are shown in Figure 4.
When an external clock signal drives the MODE/SYNC pin
at a rate faster than the chip’s internal oscillator, the
oscillator will synchronize to it. In this synchronized mode,
Burst Mode operation is disabled. The constant frequency
associated with synchronized operation provides a more
controlled noise spectrum from the converter, at the
expense of overall system efficiency of light loads.
When the oscillator’s internal logic circuitry detects a
synchronizing signal on the MODE/SYNC pin, the internal
oscillator ramp is terminated early and the slope compen-
sation is increased by approximately 30%. As a result, in
applications requiring synchronization, it is recommended
that the nominal operating frequency of the IC be pro-
grammed to be about 75% of the external clock frequency.
Attempting to synchronize to too high an external fre-
quency (above 1.3f
pensation and possible subharmonic oscillation (or jitter).
The external clock signal must exceed 2V for at least 25ns,
and should have a maximum duty cycle of 80%, as shown
in Figure 5. The MOSFET turn on will synchronize to the
rising edge of the external clock signal.
Figure 4. LTC3704 Low Output Current Operation with Burst
Mode Operation Disabled (MODE/SYNC = INTV
50mV/DIV
5A/DIV
V
OUT
I
L
TH
burst clamp is removed, allowing the I
O
) can result in inadequate slope com-
2μs/DIV
TH
pin is driven below 0.30V,
MODE/SYNC = INTV
(PULSE-SKIP MODE)
LTC3704
CC
3704 F04
CC
)
TH
3704fb
9
pin