MIC29710-5.0BT Micrel Inc, MIC29710-5.0BT Datasheet
MIC29710-5.0BT
Specifications of MIC29710-5.0BT
Related parts for MIC29710-5.0BT
MIC29710-5.0BT Summary of contents
Page 1
... These regulators use a PNP pass element that features Micrel’s proprietary Super ßeta PNP The MIC29710 is available in the 3-pin fixed output and the MIC29712 is available in the 5-pin adjustable output voltage. Both versions are fully protected against ...
Page 2
... Micrel, Inc. (1) Ordering Information Part Number Standard RoHS Compliant* MIC29710-3.3BT MIC29710-3.3WT MIC29710-5.0BT MIC29710-5.0WT MIC29712BT MIC29712WT Note: * RoHS Compliant with ‘high-melting solder’ exemption. Pin Configuration MIC29710BT/WT Pin Description Pin Number Pin Number 3-Pin TO-220 5-Pin TO-220 – – 5 October 2006 Junction Voltage Temp ...
Page 3
... Dropout Voltage ∆V = – 1%, Note 5 OUT MIC29710/29712 Ground Current MIC29710/29712 I Ground Pin V = 0.5V less than specified V GNDDO IN Current at Dropout Current Limit MIC29710/29712 Output Noise Voltage C = 47µ (10Hz to 10kHz 5.0V OUT Reference (MIC29712 only) Reference Voltage 10mA ≤ I Adjust Pin Bias Current ...
Page 4
... Output voltage temperature coefficient is defined as the worst case voltage change divided by the total temperature range ≤ V ≤ (V – 1 V), 2.4V ≤ V ≤ 8V, 10mA < I REF OUT IN IN 10. V ≤ 0.8V and V ≤ 16V OUT October 2006 + 3V. OUT ≤ 7.5A, T ≤ MAX 4 MIC29710/29712 + 1V applied OUT IN M9999-101906 ...
Page 5
... Micrel, Inc. Typical Characteristics MIC29710 Load Transient Response Test Circuit October 2006 5 MIC29710/29712 M9999-101906 ...
Page 6
... Micrel, Inc. October 2006 6 MIC29710/29712 M9999-101906 ...
Page 7
... Micrel, Inc. Functional Diagram October 2006 7 MIC29710/29712 M9999-101906 ...
Page 8
... Micrel’s ® high-current Super ßeta PNP regulators have identical pinouts. Figure 3. The MIC29710 requires only two capacitors for operation Thermal Design Linear regulators are simple to use. The most complicated design parameters to consider are thermal characteristics ...
Page 9
... Enabling the regulator requires approximately 20µA of current into the EN pin. Minimum Load Current The MIC29710/12 regulators are specified between finite loads. If the output current is to small, leakage currents dominate and the output voltage rises. A 10mA minimum load current is necessary for proper regulation. ...
Page 10
... Micrel, Inc. Package Information October 2006 3-Pin TO-220 (T) 5-Pin TO-220 (T) 10 MIC29710/29712 M9999-101906 ...
Page 11
... A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully October 2006 indemnify Micrel for any damages resulting from such use or sale. © 2004 Micrel, Incorporated. 11 MIC29710/29712 M9999-101906 ...