LM75BIM-5/NOPB National Semiconductor, LM75BIM-5/NOPB Datasheet - Page 9

• Manufacturer Part Number: LM75BIM-5/NOPB
• Description: IC TEMP SENSOR DGTL 8-SOIC
• Manufacturer: National Semiconductor

Specifications of LM75BIM-5/NOPB

• Package / Case: 8-SOIC (3.9mm Width)
• Mounting Type: Surface Mount
• Voltage - Supply: 3 V ~ 5.5 V
• Operating Temperature: -55°C ~ 125°C
• Output Type: I²C™
• Function: Temp Sensor, Watchdog
• Sensor Type: Internal
• Topology: ADC (Sigma Delta), Comparator, Register Bank
• Output Fan: Yes
• Output Alarm: Yes
• Sensing Temperature: -55°C ~ 125°C
• Ic Output Type: Digital
• Sensing Accuracy Range: ± 3°C
• Temperature Sensing Range: -55°C To +125°C
• Supply Current: 280µA
• Supply Voltage Range: 3V To 5.5V
• Resolution (bits): 9bit
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: LM75BIM-5

1.0 Functional Description
The LM75 temperature sensor incorporates a band-gap type
temperature sensor and 9-bit ADC (Sigma-Delta Analog-to-
Digital Converter). The temperature data output of the LM75
is available at all times via the I
progress, it will be stopped and restarted after the read. A
digital comparator is also incorporated that compares a series
of readings, the number of which is user-selectable, to user-
programmable setpoint and hysteresis values. The compara-
tor trips the O.S. output line, which is programmable for mode
and polarity.
The LM75B contains all the functionality of the LM75C, plus
two additional features:
1.
2.
1.1 O.S. OUTPUT, T
In Comparator mode the O.S. Output behaves like a thermo-
stat. The output becomes active when temperature exceeds
the T
ture drops below the T
can be used to turn a cooling fan on, initiate an emergency
system shutdown, or reduce system clock speed. Shutdown
mode does not reset O.S. state in a comparator mode.
In Interrupt mode exceeding T
O.S. will remain active indefinitely until reset by reading any
register via the I
by crossing T
Temperature going below T
indefinitely until being reset by a read. Placing the LM75 in
shutdown mode also resets the O.S. Output.
The LM75B has an integrated low-pass filter on both the
SDA and the SCL line. These filters increase
communications reliability in noisy environments.
The LM75B also has a bus fault timeout feature. If the
SDA line is held low for longer than t
specification) the LM75B will reset to the IDLE state (SDA
set to high impedance) and wait for a new start condition.
The TIMEOUT feature is not functional in Shutdown
Mode.
OS
limit, and leaves the active state when the tempera-
OS
, then reset, it can be activated again only by
2
C interface. Once O.S. has been activated
OS
HYST
AND T
limit. In this mode the O.S. output
HYST
OS
HYST
2
. Again, it will remain active
C bus. If a conversion is in
also makes O.S. active but
LIMITS
TIMEOUT
(see
9
1.2 POWER UP AND POWER DOWN
The LM75 always powers up in a known state. The power up
default conditions are:
1.
2.
3.
4.
5.
When the supply voltage is less than about 1.7V, the LM75 is
considered powered down. As the supply voltage rises above
the nominal 1.7V power up threshold, the internal registers
are reset to the power up default values listed above.
1.2.1 Stand-Alone Thermostat Mode
If the LM75 is not connected to the I
act as a stand-alone thermostat with the power up default
conditions listed above. It is optional, but recommended, to
connect the address pins (A2, A1, A0) and the SCL and SDA
pins together and to a 10k pull-up resistor to +V
noise immunity. Any of these pins may also be tied high sep-
arately through a 10k pull-up resistor.
1.3 I
The LM75 operates as a slave on the I
is an input (no clock is generated by the LM75) and the SDA
line is a bi-directional serial data path. According to I
specifications, the LM75 has a 7-bit slave address. The four
most significant bits of the slave address are hard wired inside
the LM75 and are “1001”. The three least significant bits of
the address are assigned to pins A2–A0, and are set by con-
necting these pins to ground for a low, (0); or to +V
(1).
Therefore, the complete slave address is:
MSB
1
2
Comparator mode
T
T
O.S. active low
Pointer = “00”
C BUS INTERFACE
OS
HYST
= 80°C
= 75°C
0
0
1
2
C bus on power up, it will
A2
2
C bus, so the SCL line
A1
www.national.com
S
S
for a high,
for better
LSB
2
A0
C bus