MCZ33810EK Freescale Semiconductor, MCZ33810EK Datasheet - Page 18

• Manufacturer Part Number: MCZ33810EK
• Description: IC IGNITION INJECTOR 32-SOIC
• Manufacturer: Freescale Semiconductor

Specifications of MCZ33810EK

• Applications: Automotive
• Current - Supply: 10mA
• Voltage - Supply: 4.5 V ~ 36 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 32-SOIC (7.5mm Width) Exposed Pad, 32-eSOIC, 32-HSOIC
• Product: Fan / Motor Controllers / Drivers
• Mounting Style: SMD/SMT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Table 5. Operational States
POWER SUPPLY
VPWR pin. The VPWR pin supplies power to all internal
regulators, analog and logic circuit blocks. The VDD supply is
used for setting communication threshold levels and
supplying power to the SO driver. This IC architecture
provides flexible microprocessor interfacing and low
quiescent current sleep mode.
POWER-ON RESET (POR)
Power On Reset (POR) and place the device in the Normal
State. The Power On Reset circuit incorporates a filter to
prevent high frequency transients from causing a POR.
HIGH regardless of the SPI control registers or the logic level
on the parallel input pins. With the OUTEN pin high, SPI
messages may be sent and received by the device. Upon
enabling the device (OUTEN low), outputs will be activated
based on the state of the command register or parallel input.
SLEEP STATE
removed from the VDD pin. In Sleep State all outputs are off.
Applying V
generates a POR.
NORMAL STATE
to the VPWR and VDD pins.
18
33810
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
The 33810 is designed to operate from 4.5 to 36 V on the
Applying V
All outputs are disabled when the OUTEN input pin is
Sleep State is entered when the V
The default Normal State is entered when power is applied
VPWR
H
H
H
H
L
L
DD
PWR
will force the device to exit the Sleep State and
VDD
H
H
H
H
and V
L
L
L
DD
OUTEN
to the device will generate a
H
X
X
X
X
X
X
L
DD
FUNCTIONAL DEVICE OPERATION
OUTPUTS
ACTIVE
supply voltage is
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OPERATIONAL MODES
NORMAL
NORMAL
STATE
SLEEP
SLEEP
Power
POR
POR
POR
Off
are as follows:
• All outputs off
• IGNITION gate driver mode enabled (IGBT Ignition Mode).
• PWM frequency and duty cycle control disabled.
• Off State open load detection enabled (LSD)
• MAXI dac set to 14 A, NOMI DAC set to 5.5A
• Spark detect level VIL DAC set to V
• Open secondary timer set to 100
• Dwell timer set 32ms
• Soft shutdown disabled
• Low-voltage flyback clamp disabled
• Dwell overlap MAXI offset disabled
MODES OF OPERATION
operation, ignition Mode, GPGD (General Purpose Gate
Driver) Mode and V10 mode.The operating mode of each
gate driver may be set individually and is programmed using
the Mode Select Command.
MODE SELECT COMMAND
mode for the GDx gate driver outputs, over/under-voltage
operation and to enable V10 Mode and the PWM generators.
The Mode Select Command programmable features are
listed below.
• Ignition/GPGD Mode select (gate drivers)
• V10 Mode enable
• Over/Under-voltage operation for all drivers
• GPGD PWM controller enable
IGNITION/GPGD MODE SELECT
determine independently, the operating mode of each of the
GDx gate driver outputs. Bits 8,9,10,11 correspond to GD0,
GD1, GD2, GD3 respectively. Setting the bit to a logic 0 sets
the GDx driver to the Ignition Mode. Setting the bit to a logic
1 commands the GDX driver to the General Purpose Mode
and disables the ignition features for that particular gate
driver (except the MAXI current shutdown feature). Further
information on GDx gate driver in Ignition Mode and General
Purpose Mode is provided later in this section of the data
sheet.
V10 MODE ENABLE BIT
for 10 cylinder applications. When the V10 Mode is enabled,
the device configures the NOMI pin and MAXI pin as digital
inputs rather than outputs. The new MAXI input pin receives
Control register settings from a Power-ON Reset (POR)
In Normal State, the 33810 gate driver has three modes of
The MODE Select Command is used to set the operating
The Ignition/General Purpose Gate Driver Mode select bits
The V10 Enable bit allows the user to configure the device
Analog Integrated Circuit Device Data
Freescale Semiconductor
μ
s
PWR
+5.5V