LTC3455EUF#TRPBF Linear Technology, LTC3455EUF#TRPBF Datasheet - Page 8

• Manufacturer Part Number: LTC3455EUF#TRPBF
• Description: IC CONV DC/DC DUAL USBBATT 24QFN
• Manufacturer: Linear Technology

Specifications of LTC3455EUF#TRPBF

• Applications: Handheld/Mobile Devices
• Voltage - Supply: 3 V ~ 6 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 24-QFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Current - Supply: -

LTC3455/LTC3455-1
PIN FUNCTIONS
FB2 (Pin 18): Feedback Pin for Switcher 2. Set the output
voltage by connecting feedback resistors to this pin.
ON2 (Pin 19): Enable Pin for Switcher 2. This pin turns on
Switcher 2 only if ON is low or PWRON is high. Switcher
2 cannot be turned on by itself.
RST (Pin 20): Reset Pin. This pin is an open-drain output
that provides a 200ms reset signal during power-up to
initialize a microcontroller.
MODE (Pin 21): Burst Mode Enable Pin. Tie this pin high
to allow Burst Mode operation for the LTC3455/LTC3455-1.
Burst Mode operation will provide superior effi ciency when
both outputs are operating with very low output currents.
Tie this pin to ground to force PWM operation under all
load current conditions. Burst Mode is disabled initially
at startup (for 200ms) and also whenever external power
is available (even if MODE is pulled high).
PWRON (Pin 22): Power-On Pin. Pull this pin high to turn
on the LTC3455/LTC3455-1. This pin is typically used in
conjunction with the ON and PBSTAT pins, and a momen-
tary-on switch. Tie PWRON to ground if not used.
SIMPLIFIED BLOCK DIAGRAM
8
OR LOW BATTERY
Li-Ion BATTERY
USE FOR LDO
3.9V TO 5.3V
3.3V TO 4.2V
USB POWER
INDICATOR
PMOS SWITCH
USB POWER
GAIN BLOCK
MANAGER
CHARGER
BATTERY
BATTERY
V
AVAILABLE INPUT POWER SOURCE
(WALL ADAPTER, USB OR BATTERY)
MAX
IS CONNECTED TO THE BEST
PBSTAT (Pin 23): Push-Button Status Pin. This pin is an
open drain output that indicates the state of the ON pin
(which is usually connected to a momentary-on push-but-
ton) to the microcontroller. This pin follows the state of the
ON pin (PBSTAT goes low when ON is pulled low).
ON (Pin 24): ON Pin. Pull this pin to ground to turn on
the LTC3455/LTC3455-1. This pin is typically used with
a momentary-on push-button switch to turn on the
LTC3455/LTC3455-1. This pin would be held low until the
PWRON pin is pulled high by a microcontroller to keep the
LTC3455/LTC3455-1 turned on. If a momentary-on switch
is not used, this pin can be held to ground to keep on the
LTC3455/LTC3455-1. Leave ON open if not used. This pin
has a weak pull-up current source.
GND (Pin 25 – Exposed Pad): Ground Pin. The exposed
backside pad is the only ground pin for the LTC3455/
LTC3455-1 and must be soldered to the PC board ground
plane for the device to operate properly.
SWITCHER 1
SWITCHER 2
HOT SWAP
3455 SBD
5V WALL ADAPTER
V
USE TO POWER OTHER
DC/DCs AND LDOs
V
1.8V TYPICAL
V
3.3V TYPICAL
HOT SWAP OUTPUT
3.3V TYPICAL
MAX
OUT1
OUT2
3455fc