MIC2045-2BTS Micrel Inc, MIC2045-2BTS Datasheet - Page 3

• Manufacturer Part Number: MIC2045-2BTS
• Description: IC DISTRIBUTION SW SGL 16-TSSOP
• Manufacturer: Micrel Inc
• Type: High Side Switchr

Specifications of MIC2045-2BTS

• Number Of Outputs: 1
• Rds (on): 30 mOhm
• Internal Switch(s): Yes
• Current Limit: Adjustable
• Voltage - Input: 0.8 ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 16-TSSOP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Pin Description
January 2005
MIC2044/2045
Pin Number
7,11,13,16
9,12,14
10
15
1
2
3
4
6
5
8
Pin Name
PWRGD
UVLOIN
/FAULT
PGREF
VBIAS
SLEW
VOUT
GND
ILIM
VIN
EN
Pin Function
Power-Good (Output): Open drain N-Channel device, active high. This pin
asserts high when the voltage at PGREF exceeds its threshold.
Switch Enable (Input): Gate control pin of the output MOSFET available as
an active high (–1) or active low (–2) input signal.
Fault Status (Output): Open drain N-Channel device, active low. This pin
indicates an overcurrent or thermal shutdown condition. For an overcurrent
event, /FAULT is asserted if the duration of the overcurrent condition lasts
longer than 32ms.
Ground connection: Tie to analog ground.
Slew-Rate Control (Input): A capacitor connected between this pin and
ground will reduce (slow) the output slew-rate. The output turn-on time must
be less than the nominal flag delay of 32ms in order to avoid nuisance
tripping of the /FAULT output since V
200mV of the voltage at the input) before the /FAULT signal delay elapses.
The slew-rate limiting capacitor requires a 16V rating or greater, 25V is
recommended. See “Applications Information: Output Slew-Rate Adjust-
ment” for further details.
Current Limit (Input): A resistor (R
sets the current limit threshold as I
factor specified in the “Electrical Characteristics” table. For the MIC2044/45,
the continuous output current range is 1A to 6A.
Undervoltage Lockout Adjust (Input): With this pin left open, the UVLO
threshold is internally set to 1.45V. When the switching voltage (V
below 1.5V, connecting an external resistive divider to this input will lower the
UVLO threshold. The total resistance of the divider must be less than 200kΩ.
To disable the UVLO, tie this pin to VIN. See “Applications Information” for
further detail.
Switch Supply (Input): Connected to the drain of the output MOSFET. The
range of input for the switch is 0.8V to 5.5V. These pins must be externally
connected together to achieve rated performance.
Switch (Output): Connected to the source of the output MOSFET. These
pins must be externally connected together to achieve rated performance.
Bias Supply (Input): This input pin supplies power to operate the switch and
internal circuitry. The input range for VBIAS is 1.6V to 5.5V. When switched
voltage (V
desired, connect VBIAS to VIN externally.
Power-Good Threshold (Input): Analog reference used to specify the
PWRGD threshold. When the voltage at this pin exceeds its threshold, V
PWRGD is asserted high. An external resistive divider network is used to
determine the output voltage level at which V
“Functional Description” for further detail. When the PWRGD signal is not
utilized, this input should be tied to VOUT.
IN
3
) is between 1.6V to 5.5V and the use of a single supply is
SET
LIMIT
OUT
) connected from this pin to ground
= CLF/R
must be “fully on” (i.e., within
TH
is exceeded. See the
SET
. CLF is the current limit
MIC2044/2045
IN
) is at or
TH
Micrel
,