FPF2026 Fairchild Semiconductor, FPF2026 Datasheet
![IC LOAD SWITCH 100MA 6-WLCSP](/photos/5/44/54465/6-bga_6-wlcsp_sml.jpg)
FPF2026
Specifications of FPF2026
Related parts for FPF2026
FPF2026 Summary of contents
Page 1
... FPF2025 pull the fault signal pin (FLAGB) low and shut-off the switch. An Auto-Restart feature turns FPF2024 and FPF2025 on again after 70ms if the ON pin is still active. The FPF2026 has a Latch-Off feature which shuts off the switch off after the expiration of the 10ms Blanking Time and keeps it off until the ON pin is toggled ...
Page 2
... PROTECTION FLAGB GND V IN UVLO ON THERMAL PROTECTION FLGAB GND ©2008 Fairchild Semiconductor Corporation FPF2024/5/6/7 Final OUT FPF2024, FPF2026, FPF2027 ON FLAGB OUT FPF2025 ON FLAGB FPF2024, FPF2026, FPF2027 CONTROL LOGIC CURRENT LIMIT FPF2025 CONTROL LOGIC CURRENT LIMIT 2 TO LOAD TO LOAD V OUT V OUT www.fairchildsemi.com ...
Page 3
... Maximum Continuous Switch Current Operating Temperature Range Storage Temperature Thermal Resistance, Junction to Ambient Electrostatic Discharge Protection Note1: Package power dissipation on 1square inch pad, 2 oz. copper board. Recommended Operating Range Parameter V IN Ambient Operating Temperature ©2008 Fairchild Semiconductor Corporation FPF2024/5/6/7 Final OUT GND ...
Page 4
... SWOFF ON IN OUT V = 5.5V 1mA IN SINK V = 1.8V 1mA IN SINK V = 5.5V 1mA, FPF2025 IN SOURCE V = 1.6V 1mA, FPF2025 IN SOURCE V = 5.5V, Switch on, IN FPF2024, FPF2026, FPF2027 3.3V 3.0V,T = 25°C LIM IN OUT A Shutdown Threshold T increasing J Return from Shutdown Hysteresis UVLO V Increasing 500Ω 0.1µ 500Ω ...
Page 5
... Temperature ( Figure 1. Shutdown Current vs.Temperature 1200 1100 1000 V 900 800 700 600 -50 -25 0 Temperature ( Figure 3. Quiescent Current vs. Temperature 350 300 250 200 150 Figure 5. R DS(ON) ©2008 Fairchild Semiconductor Corporation FPF2024/5/6/7 Final 100 - 10.4 10 1.8V IN 9.8 9.6 9.4 9 ...
Page 6
... V vs Temperature 2V/DIV V ON 2V/DIV I LOAD 10mA/DIV V OUT 2V/DIV 100us/DIV Figure 11. FPF2024 T Note3: V signal forces the device to go into overcurrent condition by loading a 7.5Ω. DRV ©2008 Fairchild Semiconductor Corporation FPF2024/5/6/7 Final. B 160 o -40 C 159 158 o - 157 o C 156 C 155 154 153 ...
Page 7
... 2V/DIV I LOAD 100mA/DIV V OUT 2V/DIV Figure 17. FPF2024 Current Limit Response (Input and enable pin are tied together and V is shorted to GND) OUT ©2008 Fairchild Semiconductor Corporation FPF2024/5/6/7 Final. B =3. 2V/DIV =0.1uF V ON 2V/DIV RESTART I LOAD 100mA/DIV V OUT ...
Page 8
... Typical Characteristics V ON 2V/DIV FLAGB 2V/DIV I LOAD 100mA/DIV V OUT 2V/DIV 10 ms/DIV Figure 19. FPF2027 Startup FLAGB Blanking Time ©2008 Fairchild Semiconductor Corporation FPF2024/5/6/7 Final 2V/DIV V =3. =10uF IN C =10uF OUT FLAGB R =5Ω L 2V/DIV I LOAD 100mA/DIV V OUT 2V/DIV Figure 20. FPF2025 =3.3V IN Device is ON ...
Page 9
... ON state. The load switch will move into the OFF state when the ON pin is inactive. In addition, FPF2026 moves into the OFF state if a current fault is encountered for longer duration than the Blanking Time. For all versions, an undervoltage on V ” ...
Page 10
... If the temperature of the die drops below the threshold temperature, the switch automatically turns- on again, To avoid unwanted thermal oscillations, a 10°C (typ) thermal hysteresis is implemented between thermal shutdown entry and exit temperatures. ©2008 Fairchild Semiconductor Corporation FPF2024/5/6/7 Final www.fairchildsemi.com ...
Page 11
... I FAULT END 70ms AUTO- RESTART 70ms Figure 21. Representative State Diagram of FPF2024/5 ©2008 Fairchild Semiconductor Corporation FPF2024/5/6/7 Final. B Notes: All States return to OFF when ON is removed. Typical timing values are shown . Key: I=Load Switch current, V=Input Voltage, T= Die Temperature I FAULT ...
Page 12
... Description of Operation cont. State Diagram for the part options with Blanking only(no Auto-Restart -FPF2026) OFF I FAULT ON STARTUP & BLANKING (Full-feature for 10ms FAULT Figure 22. Representative State Diagram of FPF2026 ©2008 Fairchild Semiconductor Corporation FPF2024/5/6/7 Final. B Notes: All States return to OFF when ON is removed. ...
Page 13
... State Diagram for the part options with no Blanking (FPF2027 & ull-feature for 10m Figure 23. Representative State Diagram of FPF2027 ©2008 Fairchild Semiconductor Corporation FPF2024/5/6/7 Final. B Notes: All States return to OFF w hen ON is rem oved. T ypical tim ing values are show n . Key : I= Load Switch current, V=Input Voltage perature EEP ( onitor SW ...
Page 14
... By turning on the Q transistor, the 7.5Ω is loaded to the =1.6V IN output voltage and simulates an over-current condition. The R2 resistor is connected between FLAGB pin and input voltage as pull-up resistor for FPF2024, FPF2026 and FPF2027 devices. The FPF2025 does not require a pull-up resistor due to its , and the Over CMOS output structure. RSTRT ...
Page 15
... Figure 25. Top Layer Figure 26. Bottom Layer Figure 27. SST ©2008 Fairchild Semiconductor Corporation FPF2024/5/6/7 Final. B Figure 28. TOP, SST and SMT 15 www.fairchildsemi.com ...
Page 16
... Dimensional Outline and Pad Layout Product FPF2024/5/6/7 1.500+/- 0.030 ©2008 Fairchild Semiconductor Corporation FPF2024/5/6/7 Final 1.000 +/-0.030 0.240 0.240 www.fairchildsemi.com ...
Page 17
... TRADEMARKS The following includes registered and unregistered trademarks and service marks, owned by Fairchild Semiconductor and/or its global subsidianries, and is not intended exhaustive list of all such trademarks. Build it Now™ CorePLUS™ CorePOWER™ CROSSVOLT™ CTL™ Current Transfer Logic™ ...