L6563S STMicroelectronics, L6563S Datasheet - Page 9

• Manufacturer Part Number: L6563S
• Description: IC PFC CTRLR TRANSITION 14SOIC
• Manufacturer: STMicroelectronics

Specifications of L6563S

• Mode: Discontinuous (Transition)
• Current - Startup: 90µA
• Voltage - Supply: 10.3 V ~ 22.5 V
• Operating Temperature: -40°C ~ 150°C
• Mounting Type: Surface Mount
• Package / Case: 14-SOIC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Frequency - Switching: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

L6563S
Table 3.
10
11
12
13
14
n°
7
8 PWM_LATCH
9
PWM_STOP
PFC_OK
Name
GND
RUN
ZCD
Vcc
GD
Pin description (continued)
PFC pre-regulator output voltage monitoring/disable function. This pin senses the output
voltage of the PFC pre-regulator through a resistor divider and is used for protection purposes.
If the voltage on the pin exceeds 2.5 V the IC stops switching and restarts as the voltage on the
pin falls below 2.4 V. However, if at the same time the voltage of the INV pin falls below 1.66V, a
feedback failure is assumed. In this case the device is latched off and the pin PWM_LATCH (#8)
is asserted high. Normal operation can be resumed only by cycling Vcc bringing its value lower
than 6V before to move up the Turn on threshold.
If the voltage on this pin is brought below 0.23 V the IC is shut down. To restart the IC the
voltage on the pin must go above 0.27 V. This can be used as a remote on/off control input.
Output pin for fault signaling. During normal operation this pin features high impedance. If a
feedback failure is detected (PFC_OK > 2.5 V and INV< 1.66V) the pin is asserted high.
Normally, this pin is used to stop the operation of the dc-dc converter supplied by the PFC pre-
regulator by invoking a latched disable of its PWM controller. If not used, the pin will be left
floating.
Output pin for fault signaling. During normal operation this pin features high impedance. If the
IC is disabled by a voltage below 0.8 V on pin RUN (#10) the voltage on the pin is pulled to
ground. Normally, this pin is used to temporarily stop the operation of the dc-dc converter
supplied by the PFC pre-regulator by disabling its PWM controller. A typical usage of this
function is brownout protection in systems where the PFC pre-regulator is the master stage. If
not used, the pin will be left floating.
Remote ON/OFF control. A voltage below 0.8V shuts down (not latched) the IC and brings its
consumption to a considerably lower level. PWM_STOP is asserted low. The IC restarts as the
voltage at the pin goes above 0.88 V. Connect this pin to pin VFF (#5) either directly or through
a resistor divider to use this function as brownout (AC mains undervoltage) protection.
Boost inductor’s demagnetization sensing input for transition-mode operation. A negative-going
edge triggers MOSFET’s turn-on.
Ground. Current return for both the signal part of the IC and the gate driver.
Gate driver output. The totem pole output stage is able to drive power MOSFET’s and IGBT’s
with a peak current of 600 mA source and 800 mA sink. The high-level voltage of this pin is
clamped at about 12 V to avoid excessive gate voltages.
Supply voltage of both the signal part of the IC and the gate driver. Sometimes a small bypass
capacitor (0.1 µF typ.) to GND might be useful to get a clean bias voltage for the signal part of
the IC.
Doc ID 16116 Rev 4
Function
Pin connection
9/43