LTC1473CGN#PBF Linear Technology, LTC1473CGN#PBF Datasheet - Page 7

• Manufacturer Part Number: LTC1473CGN#PBF
• Description: IC SWITCH DVR PWRPATH DUAL16SSOP
• Manufacturer: Linear Technology
• Series: PowerPath™r

Specifications of LTC1473CGN#PBF

• Applications: Handheld/Mobile Devices
• Fet Type: N-Channel
• Number Of Outputs: 2
• Internal Switch(s): No
• Delay Time - On: 22µs
• Delay Time - Off: 1µs
• Voltage - Supply: 4.75 V ~ 30 V
• Current - Supply: 100µA
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 16-SSOP
• No. Of Batteries: 2
• Supply Voltage Range: 4.75V To 30V
• Battery Ic Case Style: SSOP
• No. Of Pins: 16
• Operating Temperature Range: 0°C To +70°C
• Svhc: No SVHC (15-Dec-2010)
• Base Number: 1473
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

OPERATION
The LTC1473 is responsible for low-loss switching and
isolation at the “front end” of the power management
system, where up to two battery packs can be connected
and disconnected seamlessly. Smooth switching between
input power sources is accomplished with the help of
lowloss N-channel switches. They are driven by special
gate drive circuitry which limits the inrush current in and
out of the battery packs and the system power supply
capacitors.
All N-Channel Switching
The LTC1473 drives external back-to-back N-channel
MOSFET switches to direct power from two sources: the
primary battery and the secondary battery or a battery and
a wall unit. (N-channel MOSFET switches are more cost
effective and provide lower voltage drops than their P-
channel counterparts.)
Gate Drive (V
The gate drive for the low-loss N-channel switches is
supplied by an internal micropower boost regulator which
is regulated at approximately 8.5V above V
maximum. In two battery systems, the LTC1473 V
diode ORed through three external diodes connected to
the three main power sources, DCIN, BAT1 and BAT2.
Thus, V
source and will provide the overdrive required to fully
enhance the MOSFET switches.
For maximum efficiency the top of the boost regulator
inductor is connected to V
provides filtering at the top of the 1mH switched inductor,
L1, which is housed in a small surface mount package. An
internal diode directs the current from the 1mH inductor to
the V
Inrush and Short-Circuit Current Limiting
The LTC1473 uses an adaptive inrush current limiting
scheme to reduce current flowing in and out of the two
main power sources and the following system’s input
capacitor during switch-over transitions. The voltage across
a single small valued resistor, R
ascertain the instantaneous current flowing through the
GG
GG
output capacitor C2.
is regulated at 8.5V above the highest power
GG
) Power Supply
U
+
as shown in Figure 1. C1
SENSE
, is measured to
+
, up to 37V
+
pin is
two switch pairs, SW A1/B1 and SW A2/B2, during the
transitions.
Figure 2 shows a block diagram of a switch driver pair, SW
A1/B1. A bidirectional current sensing and limiting circuit
determines when the voltage drop across R
priate switch is limited during the transition period until
the inrush current subsides, generally within a few milli-
seconds, depending upon the value of the following
system’s input capacitor.
This scheme allows capacitors and MOSFET switches of
differing sizes and current ratings to be used in the same
system without circuit modifications.
BAT1
200mV. The gate-to-source voltage, V
LTC1473
V
GG
LTC1473
SW A1
DRIVERS
TO GATE
Figure 2. SW A1/B1 Inrush Current Limiting
GA1
6V
DRIVERS
SW A/B
GATE
Figure 1. V
SAB1
REGULATOR
6V
SWITCHING
SW B1
V
(8.5V + V
GG
GB1
GG
+
Switching Regulator
INRUSH CURRENT
)
BIDIRECTIONAL
V
SENSING AND
THRESHOLD
SENSE +
LIMITING
R
200mV
SENSE
V
SW
GND
V
GG
+
DCIN
V
SENSE –
L1
1mH
GS
LTC1473
BAT1
, of the appro-
SENSE
1473 F02
C2
1 F
50V
+
BAT2
1473 F01
reaches
C
OUT
OUTPUT
LOAD
C1
1 F
50V
7