VN330SPTR-E STMicroelectronics, VN330SPTR-E Datasheet - Page 6

• Manufacturer Part Number: VN330SPTR-E
• Description: IC SSR QUAD SMART 10-POWERSOIC
• Manufacturer: STMicroelectronics
• Type: High Sider
• Series: -r

Specifications of VN330SPTR-E

• Input Type: Non-Inverting
• Number Of Outputs: 4
• On-state Resistance: 200 mOhm
• Current - Output / Channel: 700mA
• Current - Peak Output: 4A
• Voltage - Supply: 10 V ~ 36 V
• Mounting Type: Surface Mount
• Package / Case: PowerSO-10 Exposed Bottom Pad
• Supply Voltage (min): 10 V
• Supply Current: 6 mA
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 25 C
• Operating Temperature: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Operating Temperature: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 497-6627-2; VN330SPTR-E

Electrical characteristics
Table 5.
1. The input voltage is internally clamped at 32V minimum, however, it is possible to connect the input pins to an higher
Table 6.
1. Status determination > 100µs after the switching edge.
Note:
6/15
Symbol
V
Symbol
V
V
I
I
I(HYST)
LGND
voltage via an external resistor that is calculated not to exceed 10mA.
V
I
I
V
DIAG
DIAGH
T
V
OVPK
LOAD
SCL
V
V
I
I
t
T
ICL
USD
LIM
TSD
IN
SC
IH
IL
OL
R
(1)
(1)
If INPUT pin is floating the corrisponding channel will automatically switch OFF. If GND pin is
disconnected, the channel will switch OFF provided V
Input low level voltage
Input high level voltage
Input hysteresis voltage
Input current
Output current in ground
disconnection
Input clamp voltage
Status voltage output low I
Status clamp voltage
Undervoltage shut down
Low state output voltage
DC Short circuit current
Peak Short circuit current V
Leakage on DIAG pin in
high state
Output leakage current
Delay time of current
limiter
Thermal shutdown
temperature
Thermal reset
temperature
Logical input
Protection and diagnostic
Parameter
Parameter
(1)
(1)
V
V
T
I
I
I
I
V
V
V
V
IN
IN
DIAG
DIAG
DIAG
J
IN
CC
IN
CC
CC
DIAG
CC
= 25°C
= 1mA
= -1mA
= 0 to 30V
= V
= V
= 24V; V
= 24V; R
= 10 to 36V; V
= 5mA ( Fault condition )
= 1mA
= -1mA
= 24V
IL
INn
; R
= GND = DIAG = 24V;
Test conditions
Test conditions
LOAD
IN
LOAD
= 30; R
< 10mΩ
< 10mΩ
IN
= V
LOAD
IL
< 10mΩ
CC
not exceed 36V.
Min.
Min
150
135
3.5
0.7
32
32
5
Typ.
Typ
-0.7
-0.7
170
155
0.5
36
36
Max.
Max
VN330SP-E
600
100
100
1.5
2.5
25
50
2
1
8
4
Unit
Unit
mA
µΑ
µΑ
µΑ
°C
°C
µs
V
V
V
V
V
V
V
V
V
V
A
A