VN5016AJTR-E STMicroelectronics, VN5016AJTR-E Datasheet

Page 1

... Thermal shut-down with automatic restart allows the device to recover normal operation as soon as fault condition disappears. Tube VN5016AJ-E Rev 7 VN5016AJ-E PowerSSO-12 pin voltage clamp protects the CC Order codes Tape & Reel VN5016AJTR-E 1/32 www.st.com 32 ...

Page 2

Contents Contents 1 Block diagram and pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2 Electrical ...

Page 3

VN5016AJ-E List of tables Table 2. Pin function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

Page 4

List of figures List of figures Figure 1. Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

Page 5

VN5016AJ-E 1 Block diagram and pin description Figure 1. Block diagram GND INPUT CS_DIS Table 2. Pin function Name V CC OUTPUT GND INPUT CURRENT SENSE CS_DIS V CC UNDERVOLTAGE CLAMP DRIVER LOGIC Pwr Battery connection. Power output. Ground connection. ...

Page 6

Block diagram and pin description Figure 2. Configuration diagram (top view) CURRENT SENSE Table 3. Suggested connections for unused and N.C. pins Connection / Pin Floating To ground (1) Not recommended. 6/ GND 2 INPUT 3 4 ...

Page 7

... These are stress ratings only and operation of the device at these or any other conditions above those indicated in the Operating sections of this specification is not implied. Exposure to the conditions in this section for extended periods may affect device reliability. Refer also to the STMicroelectronics SURE Program and other relevant quality documents. Table 4. ...

Page 8

Electrical specifications Table 4. Absolute maximum ratings (continued) Symbol Electrostatic discharge (Human Body Model: R=1.5KΩ; C=100pF) - INPUT - CURRENT SENSE V ESD - CS_DIS - OUTPUT - Charge device model (CDM-AEC-Q100-011) ESD T Junction operating temperature ...

Page 9

VN5016AJ-E 2.3 Electrical characteristics 8V<V <36V; -40°C< Table 6. Power section Symbol V Operating supply voltage CC V Undervoltage shutdown USD Undervoltage Shut-down V USDhyst hysteresis R On state resistance ON V Clamp voltage clamp I Supply current ...

Page 10

Electrical specifications Table 8. Logic input Symbol V Input low level voltage IL I Low level input current IL V Input high level voltage IH I High level input current IH V Input hysteresis voltage I(hyst) V Input clamp voltage ...

Page 11

VN5016AJ-E Table 10. Current sense (8V<V Symbol OUT OUT ( Current sense ratio drift OUT ( Current sense ratio drift 2 2 ...

Page 12

Electrical specifications Table 10. Current sense (8V<V Symbol Max analog sense V SENSE output voltage Analog sense output voltage in V SENSEH overtemperature condition Analog sense output current in I SENSEH overtemperature condition Delay response time t from falling edge ...

Page 13

VN5016AJ-E Figure 4. Current sense delay characteristics INPUT CS_DIS LOAD CURRENT SENSE CURRENT Figure 5. Delay response time between rising edge of ouput current and rising edge of current sense (CS enabled OUT I SENSE t t ...

Page 14

Electrical specifications Figure OUT out sense 6000 5500 5000 4500 4000 3500 3000 Figure 7. Maximum current sense ratio drift vs load current Note: Parameter guaranteed by design not tested. 14/32 Vs. ...

Page 15

VN5016AJ-E Figure 8. Switching characteristics Figure 9. Output voltage drop limitation V t OUT Won 80% dV /dt OUT (on) 10 INPUT t d(on out T =150 on(T) Electrical ...

Page 16

Electrical specifications Table 11. Truth table Conditions Normal operation Overtemperature Undervoltage Short circuit to GND ≤ 10 mΩ Short circuit Negative output voltage clamp (1) If the V is high, the SENSE output is at ...

Page 17

VN5016AJ-E Table 12. Electrical transient requirements ISO 7637-2: 2004(E) Test pulse (2) 5b ISO 7637-2: 2004(E) Test pulse (2) 5b (1) The above test levels must be considered referred to ...

Page 18

Electrical specifications Figure 10. Waveforms INPUT CS_DIS LOAD CURRENT SENSE CURRENT V CC INPUT CS_DIS LOAD CURRENT SENSE CURRENT INPUT CS_DIS LOAD VOLTAGE LOAD CURRENT SENSE CURRENT T j INPUT CS_DIS LOAD CURRENT SENSE CURRENT 18/32 NORMAL OPERATION UNDERVOLTAGE V ...

Page 19

VN5016AJ-E 2.4 Electrical characteristics curves Figure 11. Off state output current Iloff (uA) 2 1.75 Off State Vcc= 13V 1.5 Vin= Vout= 0V 1.25 1 0.75 0.5 0.25 0 -50 - (°C ) Figure 13. ...

Page 20

Electrical specifications Figure 17. On state resistance vs. T Ron (mOhm out Vcc= 13V -50 - (°C ) Figure 19. Undervoltage shutdown ...

Page 21

VN5016AJ-E Figure 23. CS_DIS high level voltage Vcsdh (V) 4 3.5 3 2.5 2 1.5 1 0.5 0 -50 - (°C ) Figure 25. CS_DIS low level voltage Vcsdl (V) 4 3.5 3 2.5 2 ...

Page 22

Application Information 3 Application Information Figure 26. Application schematic +5V µC 3.1 GND protection network against reverse battery 3.1.1 Solution 1 : resistor in the ground line (R This can be used with any type of load. The following is ...

Page 23

VN5016AJ-E If the calculated power dissipation leads to a large resistor or several devices have to share the same resistor then ST suggests to utilize Solution 2 (see below). 3.1.2 Solution 2 : diode (D A resistor (R =1kΩ) should ...

Page 24

Application Information 3.4 Maximum demagnetization energy (V Figure 27. Maximum turn Off current versus load inductance 100 150°C single pulse jstart 100°C repetitive pulse jstart 125°C repetitive pulse ...

Page 25

VN5016AJ-E 4 Package and PCB thermal data 4.1 PowerSSO-12™ thermal data Figure 28. PowerSSO-12™ PC board Note: Layout condition of R area= 77mm x 86mm,PCB thickness=1.6mm, Cu thickness=70µm (front and back side), Copper areas: from minimum pad lay-out to 8cm ...

Page 26

Package and PCB thermal data Figure 30. PowerSSO-12™ thermal impedance junction ambient single pulse 100 10 1 0,1 0,0001 0,001 Equation 1: pulse calculation formula ⋅ Z THδ where δ Figure 31. Thermal ...

Page 27

VN5016AJ-E Table 13. Thermal parameter Area/island (cm R1 (°C/W) R2 (°C/W) R3 (°C/W) R4 (°C/W) R5 (°C/W) R6 (°C/W) C1 (W.s/°C) C2 (W.s/°C) C3 (W.s/°C) C4 (W.s/°C) C5 (W.s/°C) C6 (W.s/° Footprint 0.1 0 ...

Page 28

Package information 5 Package information ® 5.1 ECOPACK In order to meet environmental requirements, ST offers these devices in ECOPACK® packages. These packages have a Lead-free second-level interconnect. The category of Second-Level Interconnect is marked on the package and on ...

Page 29

VN5016AJ-E Table 14. PowerSSO-12™ mechanical data Symbol ddd Millimeters Min. Typ. 1.250 0.000 1.100 0.230 0.190 4.800 3.800 0.800 5.800 0.250 0.400 0° 1.900 3.600 Package ...

Page 30

Package information 5.3 PowerSSO-12™ packing information Figure 33. PowerSSO-12™ tube shipment (no suffix) A Figure 34. PowerSSO-12™ tape and reel shipment (suffix “TR”) TAPE DIMENSIONS According to Electronic Industries Association (EIA) Standard 481 rev. A, Feb. 1986 Tape width Tape ...

Page 31

VN5016AJ-E 6 Revision history Table 15. Document revision history Date 30-Oct-2004 15-Jan-2005 11-May-2006 02-Feb-2007 02-Jul-2007 09-Jan-2007 12-Feb-2008 Revision 1 Initial release. 2 Minor text changes. 3 Document changed from Advance Data to maturity. Changes minor formatting. Added Figure 27: Maximum ...

Page 32

... Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. ...