ISL6298-2CR3Z Intersil, ISL6298-2CR3Z Datasheet - Page 7

• Manufacturer Part Number: ISL6298-2CR3Z
• Description: IC CHARGER LI-ION 4.2V 3X3 10DFN
• Manufacturer: Intersil

Specifications of ISL6298-2CR3Z

• Function: Charge Management
• Battery Type: Lithium-Ion (Li-Ion), Lithium-Polymer (Li-Pol)
• Voltage - Supply: 4.3 V ~ 6.5 V
• Operating Temperature: -20°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 10-VFDFN Exposed Pad
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Pin Description
VIN (Pin 1, 15, 16 for 4x4; Pin 1 for 3x3)
VIN is the input power source. Connect to a wall adapter.
Fault (Pin 2)
FAULT is an open-drain output indicating fault status. This
pin is pulled to LOW under any fault conditions.
Status (Pin 3)
STATUS is an open-drain output indicating charging and
inhibit states. The STATUS pin is pulled LOW when the
charger is charging a battery.
Time (Pin 4)
The TIME pin determines the oscillation period by
connecting a timing capacitor between this pin and GND.
The oscillator also provides a time reference for the charger.
GND (Pin 5)
GND is the connection to system ground.
TOEN (Pin 6 for 4x4; N/A for 3x3)
TOEN is the TIMEOUT enable input pin. Pulling this pin to
LOW disables the TIMEOUT function. Leaving this pin HIGH
or floating enables the TIMEOUT limit. For the 3x3 DFN
package, this pin is left floating internally.
Typical Applications
4x4 QFN Package Options
Adapter
5V Wall
FIGURE 16. TYPICAL APPLICATION CIRCUIT FOR THE 4x4 QFN PACKAGE OPTIONS
7
1
C
µ
1
F
D
500
R
1
1
1
C
µ
3
F
500
D
R
2
2
C
15
TIME
nF
FAULT
STATUS
VIN
TOEN
EN
V2P8
TIME
ISL6298
ISL6298
TEMP
GND
VBAT
IREF
IMIN
EN (Pin 7 for 4x4; Pin 6 for 3x3)
EN is the enable logic input. Connect the EN pin to LOW to
disable the charger or leave it floating to enable the charger.
V2P8 (Pin 8 for 4x4; Pin 7 for 3x3)
This is a 2.8V reference voltage output. This pin outputs a
2.8V voltage source when the input voltage is above POR
threshold and outputs zero otherwise. The V2P8 pin can be
used as an indication for adapter presence.
IREF (Pin 9 for 4x4; Pin 8 for 3x3)
This is the programming input for the constant charging
current.
IMIN (Pin 10 for 4x4; N/A for 3x3)
IMIN is the programmable input for the end-of-charge
current. For the 3x3 DFN package, this pin is shorted to the
V2P8 pin internally.
TEMP (Pin 11 for 4x4; Pin 9 for 3x3)
TEMP is the input for an external NTC thermistor. The TEMP
pin is also used for battery removal detection.
VBAT (Pin 12, 13, 14 for 4x4; Pin 10 for 3x3)
VBAT is the connection to the battery. Typically a 10µF
Tantalum capacitor is needed for stability when there is no
battery attached. When a battery is attached, only a 1µF
ceramic capacitor is required.
R
80
IMIN
k
1 F
C
µ
2
V2P8
R
U
R
R
80
IREF
T
k
T
Battery
Pack
March 9, 2006
FN9173.4