AT45DB081D-SU Atmel, AT45DB081D-SU Datasheet - Page 13

• Manufacturer Part Number: AT45DB081D-SU
• Description: IC FLASH 8MBIT 66MHZ 8SOIC
• Manufacturer: Atmel

Specifications of AT45DB081D-SU

• Format - Memory: FLASH
• Memory Type: DataFLASH
• Memory Size: 8M (4096 pages x 264 bytes)
• Speed: 66MHz
• Interface: SPI, RapidS
• Voltage - Supply: 2.7 V ~ 3.6 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-SOIC (5.3mm Width), 8-SOP, 8-SOEIAJ
• Architecture: Sectored
• Interface Type: SPI
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 2.7 V
• Maximum Operating Current: 15 mA
• Mounting Style: SMD/SMT
• Organization: 64 KB x 16
• Memory Configuration: 4096 Pages X 264 Bytes
• Clock Frequency: 50MHz
• Supply Voltage Range: 2.5V To 3.6V, 2.7V To 3.6V
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

9. Hardware Controlled Protection
Figure 9-1.
Table 9-1.
3596M–DFLASH–5/10
Period
Time
1
2
3
WP
WP Pin
WP Pin and Protection Status
WP Pin and Protection Status
High
High
Low
If the device is power cycled, then the software controlled protection will be disabled. Once the
device is powered up, the Enable Sector Protection command should be reissued if sector pro-
tection is desired and if the WP pin is not used.
Sectors specified for protection in the Sector Protection Register and the Sector Protection Reg-
ister itself can be protected from program and erase operations by asserting the WP pin and
keeping the pin in its asserted state. The Sector Protection Register and any sector specified for
protection cannot be erased or reprogrammed as long as the WP pin is asserted. In order to
modify the Sector Protection Register, the WP pin must be deasserted. If the WP pin is perma-
nently connected to GND, then the content of the Sector Protection Register cannot be changed.
If the WP pin is deasserted, or permanently connected to V
Protection Register can be modified.
The WP pin will override the software controlled protection method but only for protecting the
sectors. For example, if the sectors were not previously protected by the Enable Sector Protec-
tion command, then simply asserting the WP pin would enable the sector protection within the
maximum specified t
would no longer be enabled (after the maximum specified t
tor Protection command was not issued while the WP pin was asserted. If the Enable Sector
Protection command was issued before or while the WP pin was asserted, then simply deassert-
ing the WP pin would not disable the sector protection. In this case, the Disable Sector
Protection command would need to be issued while the WP pin is deasserted to disable the sec-
tor protection. The Disable Sector Protection command is also ignored whenever the WP pin is
asserted.
A noise filter is incorporated to help protect against spurious noise that may inadvertently assert
or deassert the WP pin.
The table below details the sector protection status for various scenarios of the WP pin, the
Enable Sector Protection command, and the Disable Sector Protection command.
Command Issued During Period 1
Command Not Issued Previously
1
Enable Sector Protection
Issue Command
Issue Command
Command
or 2
X
–
–
WPE
time. When the WP pin is deasserted; however, the sector protection
Protection Command
2
Issue Command
Issue Command
Disable Sector
Not Issued Yet
X
X
–
–
Atmel AT45DB081D
WPD
Sector Protection
CC
time) as long as the Enable Sec-
, then the content of the Sector
Disabled
Disabled
Disabled
Enabled
Enabled
Enabled
Enabled
Status
3
Protection
Read/Write
Read/Write
Read/Write
Read/Write
Read/Write
Read/Write
Read Only
Register
Sector
13