AT27C516-70JC Atmel, AT27C516-70JC Datasheet

Page 1

... Any word can be accessed in less than 45 ns, eliminating the need for speed reducing WAIT states. The by-16 organization make this part ideal for high-performance 16- and 32-bit microprocessor systems. In read mode, the AT27C516 typically consumes 15 mA. Standby mode supply cur- rent is typically less than 10 A. Pin Configurations ...

Page 2

... The AT27C516 is available in industry standard JEDEC- approved one-time programmable (OTP) plastic PLCC and VSOP packages. The device features two-line control (CE, OE) to eliminate bus contention in high-speed systems. With 32K word storage capability, the AT27C516 allows firmware to be stored reliably and to be accessed by the system without the delays of mass storage media. Atmel’ ...

Page 3

Absolute Maximum Ratings* Temperature Under Bias ................................ -55°C to +125°C Storage Temperature ..................................... -65°C to +150°C Voltage on Any Pin with Respect to Ground .........................................-2.0V to +7.0V Voltage on A9 with Respect to Ground ......................................-2.0V to +14.0V V Supply Voltage ...

Page 4

... SB1 CC I (TTL 2 SB2 MHz mA OUT -400 and removed simultaneously with or after except during programming. The supply current would then be the sum AT27C516 -70 -85 0°C - 70°C 0°C - 70°C -40°C - 85°C -40°C - 85°C 5V 10% 5V 10% Min Max 0.3V 100 + 0.5V ...

Page 5

... This parameter is only sampled and is not 100% tested. 5. Output float is defined as the point when data is no longer driven. (1) -45 -55 Min Max Min after the falling edge of CE without impact after the address is valid without impact on t ACC OE AT27C516 -70 -85 Max Min Max Min Max 0.0V and 0.8V and ...

Page 6

... R F Pin Capacitance ( MHz 25°C Symbol Typ OUT Note: 1. Typical values for nominal supply voltage. This parameter is only sampled and is not 100% tested. AT27C516 6 Output Test Load Note: C capacitance, except -45, -55, and -70 devices, where C Max Units 100 pF including jig pF. ...

Page 7

... Programming Waveforms Notes: 1. The Input Timing Reference is 0.8V for and t are characteristics of the device but must be accommodated by the programmer. OE DFP 3. When programming the AT27C516 at 0.1 µF capacitor is required across V transients. DC Programming Characteristics 5° 6.5 0.25V Symbol Parameter I Input Load Current LI V Input Low Level ...

Page 8

... This parameter is only sampled and is not 100% tested. Output Float is defined as the point where data is no longer driven— see timing diagram. 3. Program Pulse width tolerance is 50 sec Atmel’s 27C516 Integrated Product Identification Code Codes A0 Manufacturer 0 Device Type 1 AT27C516 8 = 13.0 0.25V PP (1) Test Conditions Input Rise and Fall Times: (10 Input Pulse Levels: ...

Page 9

Rapid Programming Algorithm PGM pulse width is used to program. The address is set to the first location raised to 6.5V and V CC raised to 13.0V. Each address is first programmed with one 50 ...

Page 10

... Plastic J-Leaded Chip Carrier (PLCC) 40V 40-Lead, Plastic Thin Small Outline Package (VSOP) (10mm x 14mm) AT27C516 10 Ordering Code AT27C516-45JC AT27C516-45VC AT27C516-45JI AT27C516-45VI AT27C516-55JC AT27C516-55VC AT27C516-55JI AT27C516-55VI AT27C516-70JC AT27C516-70VC AT27C516-70JI AT27C516-70VI AT27C516-85JC AT27C516-85VC AT27C516-85JI AT27C516-85VI AT27C516-10JC AT27C516-10VC AT27C516-10JI AT27C516-10VI Package Type Package ...

Page 11

Packaging Information 44J, 44-Lead, Plastic J-Leaded Chip Carrier (PLCC) Dimensions in Inches and (Millimeters) JEDEC STANDARD MS-018 AC .045(1.14) X 45° PIN NO. 1 IDENTIFY .656(16.7) .650(16.5) .032(.813) .695(17.7) .026(.660) .685(17.4) .050(1.27) TYP .500(12.7) REF SQ .022(.559) X 45° MAX ...

Page 12

... No licenses to patents or other intellectual prop Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel’s products are not authorized for use as critical components in life suppor t devices or systems. ...