DS1245ABP-70IND Maxim Integrated Products, DS1245ABP-70IND Datasheet - Page 2
![IC NVSRAM 1MBIT 70NS 34PCM](/photos/6/58/65856/406-34-pcm_sml.jpg)
DS1245ABP-70IND
Manufacturer Part Number
DS1245ABP-70IND
Description
IC NVSRAM 1MBIT 70NS 34PCM
Manufacturer
Maxim Integrated Products
Datasheet
1.DS1245YP-100.pdf
(10 pages)
Specifications of DS1245ABP-70IND
Format - Memory
RAM
Memory Type
NVSRAM (Non-Volatile SRAM)
Memory Size
1M (128K x 8)
Speed
70ns
Interface
Parallel
Voltage - Supply
4.75 V ~ 5.25 V
Operating Temperature
-40°C ~ 85°C
Package / Case
34-PowerCap™ Module
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
DESCRIPTION
The DS1245 1024k Nonvolatile SRAMs are1,048,576-bit, fully static, nonvolatile SRAMs organized as
131,072 words by 8 bits. Each complete NV SRAM has a self-contained lithium energy source and
control circuitry which constantly monitors V
occurs, the lithium energy source is automatically switched on and write protection is unconditionally
enabled to prevent data corruption. DIP-package DS1245 devices can be used in place of existing 128k x
8 static RAMs directly conforming to the popular bytewide 32-pin DIP standard. DS1245 devices in the
PowerCap Module package are directly surface mountable and are normally paired with a DS9034PC
PowerCap to form a complete Nonvolatile SRAM module. There is no limit on the number of write
cycles that can be executed and no additional support circuitry is required for microprocessor interfacing.
READ MODE
The DS1245 executes a read cycle whenever
and
A
data output drivers within t
then data access must be measured from the later occurring signal (
is either t
WRITE MODE
The DS1245 executes a write cycle whenever the
inputs are stable. The later occurring falling edge of
The write cycle is terminated by the earlier rising edge of
valid throughout the write cycle.
before another cycle can be initiated. The
cycles to avoid bus contention. However, if the output drivers are enabled (
will disable the outputs in t
DATA RETENTION MODE
The DS1245AB provides full functional capability for V
4.5 volts. The DS1245Y provides full functional capability for V
protects by 4.25 volts. Data is maintained in the absence of V
The nonvolatile static RAMs constantly monitor V
automatically write-protect themselves, all inputs become “don’t care,” and all outputs become high
impedance. As V
energy source to RAM to retain data. During power-up, when V
the power switching circuit connects external V
Normal RAM operation can resume after V
DS1245Y.
FRESHNESS SEAL
Each DS1245 device is shipped from Maxim with its lithium energy source disconnected, guaranteeing
full energy capacity. When V
is enabled for battery back-up operation.
CE
16
) defines which of the 131,072 bytes of data is to be accessed. Valid data will be available to the eight
and
OE
(Output Enable) are active (low). The unique address specified by the 17 address inputs (A
OE
CO
for
(Output Enable) access times are also satisfied. If
CE
CC
or t
falls below approximately 3.0 volts, a power switching circuit connects the lithium
OE
for
ODW
ACC
CC
OE
from its falling edge.
(Access Time) after the last address input signal is stable, providing that
is first applied at a level greater than 4.25 volts, the lithium energy source
rather than address access.
WE
must return to the high state for a minimum recovery time (t
OE
CC
CC
WE
exceeds 4.75 volts for the DS1245AB and 4.5 volts for the
control signal should be kept inactive (high) during write
for an out-of-tolerance condition. When such a condition
CC
(Write Enable) is inactive (high) and
CC
to RAM and disconnects the lithium energy source.
2 of 10
CE
WE
. Should the supply voltage decay, the NV SRAMs
or
CC
and
WE
CE
greater than 4.75 volts and write protects by
CC
CE
OE
will determine the start of the write cycle.
or
without any additional support circuitry.
CC
signals are active (low) after address
and
CE
WE
CC
rises above approximately 3.0 volts,
or
. All address inputs must be kept
greater than 4.5 volts and write-
CE
OE
access times are not satisfied,
CE
) and the limiting parameter
and
OE
CE
active) then
(Chip Enable)
DS1245Y/AB
WE
WR
0
-
)