M25PE80-VMP6TG NUMONYX, M25PE80-VMP6TG Datasheet - Page 30

• Manufacturer Part Number: M25PE80-VMP6TG
• Description: IC FLASH 8MBIT 75MHZ 8VFQFPN
• Manufacturer: NUMONYX
• Series: Forté™r

Specifications of M25PE80-VMP6TG

• Format - Memory: FLASH
• Memory Type: FLASH
• Memory Size: 8M (1M x 8)
• Speed: 75MHz
• Interface: SPI, 3-Wire Serial
• Voltage - Supply: 2.7 V ~ 3.6 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-VFQFN, 8-VFQFPN
• Cell Type: NOR
• Density: 8Mb
• Access Time (max): 8ns
• Interface Type: Serial (SPI)
• Boot Type: Not Required
• Address Bus: 1b
• Operating Supply Voltage (typ): 3.3V
• Operating Temp Range: -40C to 85C
• Package Type: VFQFPN
• Program/erase Volt (typ): 2.7 to 3.6V
• Sync/async: Synchronous
• Operating Temperature Classification: Industrial
• Operating Supply Voltage (min): 2.7V
• Operating Supply Voltage (max): 3.6V
• Word Size: 8b
• Number Of Words: 1M
• Supply Current: 8mA
• Mounting: Surface Mount
• Pin Count: 8
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: M25PE80-VMP6TG; M25PE80-VMP6TGTR

Instructions
6.7
30/66
Read data bytes at higher speed (FAST_READ)
The device is first selected by driving Chip Select (S) Low. The instruction code for the read
data bytes at higher speed (FAST_READ) instruction is followed by a 3-byte address (A23-
A0) and a dummy byte, each bit being latched-in during the rising edge of Serial Clock (C).
Then the memory contents, at that address, is shifted out on serial data output (Q), each bit
being shifted out, at a maximum frequency f
The instruction sequence is shown in
The first byte addressed can be at any location. The address is automatically incremented
to the next higher address after each byte of data is shifted out. The whole memory can,
therefore, be read with a single read data bytes at higher speed (FAST_READ) instruction.
When the highest address is reached, the address counter rolls over to 000000h, allowing
the read sequence to be continued indefinitely.
The read data bytes at higher speed (FAST_READ) instruction is terminated by driving Chip
Select (S) High. Chip Select (S) can be driven High at any time during data output. Any read
data bytes at higher speed (FAST_READ) instruction, while an erase, program or write cycle
is in progress, is rejected without having any effects on the cycle that is in progress.
Figure 13. Read data bytes at higher speed (FAST_READ) instruction sequence
1. Address bits A23 to A20 are don’t care.
S
C
D
Q
S
C
D
Q
0
and data-out sequence
7
1
32 33 34
High Impedance
6
2
Instruction
Dummy byte
5
3
4
4
35
3
5
36 37 38 39 40 41 42 43 44 45 46
2
6
1
7
23
0
8
MSB
22 21
7
9 10
Figure
24-bit address
6
DATA OUT 1
5
C
13.
, during the falling edge of Serial Clock (C).
3
28 29 30 31
4
2
3
1
2
0
1
0
47
MSB
7
6
DATA OUT 2
5
4
3
2
1
0
M25PE80
AI04006
MSB
7