25LC1024-I/SM Microchip Technology, 25LC1024-I/SM Datasheet - Page 18

• Manufacturer Part Number: 25LC1024-I/SM
• Description: IC EEPROM 1MBIT 20MHZ 8SOIC
• Manufacturer: Microchip Technology

Specifications of 25LC1024-I/SM

• Memory Size: 1M (128K x 8)
• Package / Case: 8-SOIC (5.3mm Width), 8-SOP, 8-SOEIAJ
• Operating Temperature: -40°C ~ 85°C
• Format - Memory: EEPROMs - Serial
• Memory Type: EEPROM
• Speed: 20MHz
• Interface: SPI, 3-Wire Serial
• Voltage - Supply: 2.5 V ~ 5.5 V
• Organization: 128 K x 8
• Interface Type: SPI
• Maximum Clock Frequency: 20 MHz
• Access Time: 50 ns
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.5 V
• Maximum Operating Current: 10 mA
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Operating Supply Voltage: 2.5 V, 5.5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

25LC1024
2.12
Once the device has entered Deep Power-Down
mode all instructions are ignored except the release
from Deep Power-down and Read Electronic Signa-
ture command. This command can also be used when
the device is not in Deep Power-down, to read the
electronic signature out on the SO pin unless another
command is being executed such as Erase, Program
or Write STATUS register.
FIGURE 2-12:
Driving CS high after the 8-bit RDID command, but before the Electronic Signature has been transmitted, will still
ensure the device will be taken out of Deep Power-Down mode. However, there is a delay T
device returns to Standby mode (I
FIGURE 2-13:
DS22064D-page 18
SCK
SO
CS
SI
RELEASE FROM DEEP
POWER-DOWN AND READ
ELECTRONIC SIGNATURE
1
0
SCK
SO
CS
SI
0
1
1
Instruction
2
RELEASE FROM DEEP POWER-DOWN AND READ ELECTRONIC SIGNATURE
RELEASE FROM DEEP POWER-DOWN AND READ ELECTRONIC SIGNATURE
1
0
0
3
0
1
1
4
1
Instruction
2
0
CCS
5
0
High-Impedance
3
), as shown in Figure 2-13.
1
6
1
4
1
7
0
23 22 21 20
5
8
High-Impedance
1
6
9 10 11
1
7
24-bit Address
Release from Deep Power-Down mode and Read
Electronic Signature is entered by driving CS low,
followed by the RDID instruction code (Figure 2-12)
and then a dummy address of 24 bits (A23-A0). After
the last bit of the dummy address is clocked in, the
8-bit Electronic signature is clocked out on the SO
pin.
After the signature has been read out at least once,
the sequence can be terminated by driving CS high.
The device will then return to Standby mode and will
wait to be selected so it can be given new instructions.
If additional clock cycles are sent after the electronic
signature has been read once, it will continue to output
the signature on the SO line until the sequence is
terminated.
29 30 31 32 33 34 35 36 37 38 39
2
1
0
T
REL
7
0
Electronic Signature Out
Manufacturers ID 0x29
6
0
 2010 Microchip Technology Inc.
5
1
REL
4
0
that occurs before the
3
1
2
0
1
0
0
1