MAX4267EUA-T Maxim Integrated, MAX4267EUA-T Datasheet - Page 15

• Manufacturer Part Number: MAX4267EUA-T
• Description: High Speed Operational Amplifiers Single-Supply 300MHz w/Enable
• Manufacturer: Maxim Integrated

Specifications of MAX4267EUA-T

• Number Of Channels: 1
• Voltage Gain Db: 95 dB
• Input Offset Voltage: 1 mV (Typ) at 5 V
• Slew Rate: 900 V/us at 5 V
• Operating Supply Voltage: 5 V
• Maximum Operating Temperature: + 85 C
• Package / Case: uMAX
• Common Mode Rejection Ratio (min): 60 dB
• Maximum Power Dissipation: 330 mW
• Minimum Operating Temperature: - 40 C
• Supply Voltage - Max: 8 V
• Supply Voltage - Min: 4.5 V

Figure 4b. MAX4269 Small-Signal Gain vs. Frequency With
Isolation Resistor
The MAX4265–MAX4270 operate from a single +4.5V
to +8.0V supply or in a dual-supply configuration.
When operating with a single supply, connect the V
pins directly to the ground plane. Bypass V
ground with ceramic chip capacitors. Due to the
MAX4265–MAX4270s’ wide bandwidth, use a 1nF
capacitor in parallel with a 0.1µF to 1µF capacitor. If the
device is located more than 10cm from the power sup-
ply, adding a larger bulk capacitor will improve perfor-
mance.
When operating with dual supplies, ensure that the total
voltage across the device (V
exceed +8V. Therefore, supplies of ±2.5V, ±3.3V, and
asymmetrical supplies are possible. For example, oper-
ation with V
voltage swing for the negative pulses found in video
signals. When operating with dual supplies, the V
pins and the V
same guidelines stated in the paragraph above.
Power Supplies, Bypassing, and Layout
-1
-2
-3
-4
-5
CC
5
4
3
2
1
0
0.1M
= +5V and V
EE
______________________________________________________________________________________
pins should be bypassed using the
1M
FREQUENCY (Hz)
10M
EE
C
R
C
R
ISO
L
ISO
= -3V provides sufficient
L
C
R
= 10pF
ISO
= 10pF
L
CC
= 12Ω
= 15Ω
= 10pF
= 18Ω
100M
to V
EE
400MHz Op Amps with Disable
1G
) does not
CC
CC
EE
to
Ultra-Low-Distortion, +5V,
Because the MAX4265–MAX4270 have high band-
width, circuit layout becomes critical. A solid ground
plane provides a low-inductance path for high-speed
transient currents. Use multiple vias to the ground
plane for each bypass capacitor. If V
ground, use multiple vias here, too. Avoid sharing
ground vias with other signals to reduce crosstalk
between circuit sections.
Avoid stray capacitance at the op amp’s inverting
inputs. Stray capacitance, in conjunction with the feed-
back resistance, forms an additional pole in the cir-
cuit’s transfer function, with its associate phase shift.
Minimizing the trace lengths connected to the inverting
input helps minimize stray capacitance.
MAX4265/66/67 TRANSISTOR COUNT: 132
MAX4268/69/70 TRANSISTOR COUNT: 285
PROCESS: Bipolar
Figure 4c. MAX4270 Small-Signal Gain vs. Frequency With
Isolation Resistor
-1
-2
-3
-4
-5
-6
4
3
2
1
0
0.1M
1M
FREQUENCY (Hz)
10M
Chip Information
C
R
C
R
L
ISO
C
R
ISO
L
= 22pF
ISO
L
= 22pF
= 3.9Ω
= 22pF
= 6Ω
= 22Ω
100M
EE
is connected to
1G
15