GLS55VD020-60-I-TQWE-TM024 Greenliant, GLS55VD020-60-I-TQWE-TM024 Datasheet
GLS55VD020-60-I-TQWE-TM024
Specifications of GLS55VD020-60-I-TQWE-TM024
Related parts for GLS55VD020-60-I-TQWE-TM024
GLS55VD020-60-I-TQWE-TM024 Summary of contents
Page 1
... The NAND Controller uses SuperFlash ogy and is factory pre-programmed with an embedded flash file system. Upon initial power-on, the GLS55VD020 recognizes attached flash media devices, sets up a bad block table, executes all necessary handshaking routines for flash media support, and, finally, performs the low-level format ...
Page 2
... ATA/IDE interface. The GLS55VD020 high-performance NAND Controller offers sustained read and write performance up to 30.0 MB/sec. The GLS55VD020 directly supports flash media devices or, through simple decoding logic, can support flash media devices. The controller also provides a WP#/PD# pin to protect criti- © ...
Page 3
... NAND Controller GLS55VD020 GENERAL DESCRIPTION The NAND Controller contains a microcontroller and embedded flash file system integrated in TQFP and VFBGA packages. Refer to Figure 1 for the NAND Control- ler block diagram. The controller interfaces with the host system allowing data to be written to and read from the flash media ...
Page 4
... Embedded Flash File System SRAM Buffer HOST ATA/IDE BUS FIGURE 1: NAND C ONTROLLER ©2010 Greenliant Systems, Ltd. NAND Controller MCU ECC Internal DMA PMU SCI B D LOCK IAGRAM 4 NAND Controller GLS55VD020 NAND Flash Media Dual Channel NAND Flash Media 1355 B1.1 S71355-05-000 05/10 ...
Page 5
... NAND Controller GLS55VD020 PIN ASSIGNMENTS The signal/pin assignments are listed in Table 2. Low active signals have a “#” suffix. Pin types are Input, Output, or Input/Output. Signals whose source is the host are desig- nated as inputs while signals that the NAND Controller sources are outputs. ...
Page 6
... D14 D12 D9 DASP# VSS CS3FX# PDIAG# IOWR# VSS VDDQ D10 VSS 85- VFBGA (MVW) BALL 6 NAND Controller GLS55VD020 VSS RESET# D7 DNU TIE_DN VSS FWE# FCE5# FCE4# FCLE FCE3# VSS FCE0# VDD V FCE1# REG SCIDOUT SCIDIN VDD SCICLK 1355 85-vfbga MW P1 ...
Page 7
... NAND Controller GLS55VD020 TABLE SSIGNMENTS Pin No. 100- 85- Symbol TQFP VFBGA Host Side Interface D15 65 D3 D14 66 E2 D13 67 E3 D12 68 F2 D11 70 F3 D10 H10 ...
Page 8
... Active Low Flash Media Chip Read Active Low Flash Media Chip Write O O5 Active High Flash Media Chip Command Latch Enable Active High Flash Media Chip Address Latch Enable I/O I3U/O5 Flash Media Chip High Byte Address/Data Bus pins 8 NAND Controller GLS55VD020 signal level S71355-05-000 05/10 ...
Page 9
... NAND Controller GLS55VD020 TABLE SSIGNMENTS ONTINUED Pin No. 100- 85- Symbol TQFP VFBGA FAD7 45 C4 FAD6 43 A4 FAD5 41 B5 FAD4 39 C6 FAD3 34 B7 FAD2 32 C8 FAD1 30 A8 FAD0 28 A9 FCE7 FCE6 FCE5 FCE4 FCE3 FCE2 ...
Page 10
... Analog input is connected to V for supply voltage detection DD 3. All DNU pins should not be connected. ©2010 Greenliant Systems, Ltd Pin I/O 1 Type Type Name and Functions Pin needs to be connected Not Use, must be left unconnected. 10 NAND Controller GLS55VD020 SS. T0-0.3 1355 S71355-05-000 05/10 ...
Page 11
... Cylinders, Heads, and Sectors can be re-configured from the default settings during the manufacturing process. 3. Cylinders, Heads, and Sectors are not applicable for these capacities. Only LBA addressing applies. Functional Specifications Table 3 shows the performance and the maximum capacity supported by GLS55VD020. TABLE 3: Functional Specification of GLS55VD020 Functions ...
Page 12
... SCICLK. OUT IN Security Features The GLS55VD020 NAND Controller offers the standard ATA Security Mode Feature Set, a password system that restricts the access of user data stored in the device. For additional data security features, please contact Greenliant. ©2010 Greenliant Systems, Ltd. NAND Controller ...
Page 13
... NAND Controller GLS55VD020 CONFIGURABLE WRITE PROTECT/POWER-DOWN MODES The WP#/PD# pin can be used for either Write Protect mode or Power-down mode, but only one mode is active at any time. Either mode can be selected through the host command, Set-WP#/PD#-Mode, explained in Section . Once the mode is set with this command, the pin will stay in the configured mode until the next time this command is issued. ...
Page 14
... Rise Time should be faster than or equal to POR# Rise Time Fall Time should be slower than or equal to POR# Fall Time. DD ©2010 Greenliant Systems, Ltd 10% 90% Symbol NAND Controller GLS55VD020 T F 10% 90% 1355 F23.0 Min Max Units 250 ms 250 ms T0-0.0 1355 S71355-05-000 05/10 ...
Page 15
... NAND Controller GLS55VD020 I/O TRANSFER FUNCTION The default operation for the NAND Controller is 16-bit. However, if the host issues a Set-Feature command to enable 8-bit mode, the NAND Controller permits 8-bit data access. The following table defines the function of various operations. TABLE 5: I/O Function Function Code ...
Page 16
... Cylinder High (LBA 23-16) 0 Drive/Head 1 Status 0 Alternate Status IDNF 0 ABRT 16 NAND Controller GLS55VD020 Registers IOWR (IORD#=1) Data (Write) Feature Sector Count Sector Number (LBA 7-0) Cylinder Low (LBA 15-8) Cylinder High (LBA 23-16) Drive/Head Command Device Control T0-0.0 1355 D1 D0 Reset Value 0 AMNF 0000 0000b ...
Page 17
... NAND Controller GLS55VD020 Feature Register (Write Only) This register provides additional command-specific parameters to the NAND Controller. Sector Count Register This register contains the numbers of sectors of data requested to be transferred on a Read or Write operation between the host and the NAND Controller. If the value in this register is zero, a count of 256 sectors is spec- ified ...
Page 18
... Table 7 summarizes the NAND Controller command set. TABLE 7: NAND Controller Command Set ( Command Check-Power-Mode ©2010 Greenliant Systems, Ltd Rst X 1 Code FR E5H or 98H - 18 NAND Controller GLS55VD020 D1 D0 Reset Value -IEn 0 0000 1000b LBA ...
Page 19
... NAND Controller GLS55VD020 TABLE 7: NAND Controller Command Set (Continued Command Execute-Drive-Diagnostic Erase-Sector(s) Flush-Cache Format-Track Identify-Drive Idle Idle-Immediate Initialize-Drive-Parameters NOP Read-Buffer Read-DMA Read-Multiple Read-Sector(s) Read-Verify-Sector(s) Recalibrate Request-Sense Security-Disable-Password Security-Erase-Prepare Security-Erase-Unit Security-Freeze-Lock Security-Set-Password Security-Unlock Seek Set-Features SMART Set-Multiple-Mode Set-Sleep-Mode Set-WP#/PD#-Mode Standby ...
Page 20
... Firmware revision in ASCII. Big Endian Byte Order in Word User Definable Model number Maximum number of sectors on Read/Write-Multiple command Reserved Capabilities Reserved PIO data transfer cycle timing mode Reserved Translation parameters are valid Current numbers of cylinders Current numbers of heads 20 NAND Controller GLS55VD020 S71355-05-000 05/10 ...
Page 21
... NAND Controller GLS55VD020 TABLE 8: Identify-Drive Information (Continued Word Default Total 1 Address Value Bytes 56 nnnnH 2 57-58 nnnnH 4 59 010X 2 60-61 nnnnH 4 62 0000H 2 63 0x07H 2 64 0003H 2 65 0078H 2 66 0078H 2 67 0078H 2 68 0078H 2 69-79 0000H 22 80 007EH 2 81 0019H 2 82 706BH 2 83 ...
Page 22
... Word 59: Multiple Sector Setting This field contains a validity flag in the Odd Byte and the current number of sectors that can be transferred per interrupt for Read/Write Multiple in the Even Byte. The Odd Byte is always 01H which indicates that the Even Byte is always valid. ©2010 Greenliant Systems, Ltd. NAND Controller 22 GLS55VD020 S71355-05-000 05/10 ...
Page 23
... NAND Controller GLS55VD020 The Even Byte value depends on the value set by the Set Multiple command. The Even Byte of this word by default contains a 00H which indicates that Read/Write Multiple commands are not valid. Word 60-61: Total Sectors Addressable in LBA Mode This field contains the number of sectors addressable for the NAND Controller in LBA mode only ...
Page 24
... Word 80: Major Version Number If not 0000H or FFFFH, the device claims compliance with the major version(s) as indicated by bits (6:1) being set to one. Since ATA standards maintain downward compatibility, a device may set more than one bit. GLS55VD020 supports ATA-1 to ATA-6. Word 81: Minor Version Number If an implementer claims that the revision of the standard they used to guide their implementation does not need to be reported or if the implementation was based upon a standard prior to the ATA-3 standard, word 81 should be 0000H or FFFFH ...
Page 25
... NAND Controller GLS55VD020 Bit Function 15 0: Provides indication that the features/command sets supported words are not valid 14 1: Provides indication that the features/command sets supported words are valid 13-9 0: Reserved 8 0: Set-Max security extension is not supported 7-5 0: Reserved 4 0: Removable Media Status feature set is not supported ...
Page 26
... Ultra DMA mode 4 and below are supported 3 1: Ultra DMA mode 3 and below are supported 2 1: Ultra DMA mode 2 and below are supported 1 1: Ultra DMA mode 1 and below are supported 0 1: Ultra DMA mode 0 is supported ©2010 Greenliant Systems, Ltd. NAND Controller 26 GLS55VD020 S71355-05-000 05/10 ...
Page 27
... NAND Controller GLS55VD020 Word 89: Time required for Security erase unit completion Word 89 specifies the time required for the Security Erase Unit command to complete. Value Time 0 Value not specified 1-254 (Value * 2) minutes 255 >508 minutes Word 90: Time required for Enhanced security erase unit completion Word 90 specifies the time required for the Enhanced Security Erase Unit command to complete ...
Page 28
... Advanced True IDE Multiword DMA Mode Support Indicates the maximum True IDE Multiword DMA mode supported by the card Value 3-7 ©2010 Greenliant Systems, Ltd. Time Specified in word 64 PIO Mode 5 PIO Mode 6 Reserved Time Specified in word 63 Multiword DMA Mode 3 Multiword DMA Mode 4 Reserved 28 NAND Controller GLS55VD020 S71355-05-000 05/10 ...
Page 29
... NAND Controller GLS55VD020 8-6 Advanced True IDE PIO Mode Selected Indicates the current True IDE PIO mode selected on the card Value 3-7 11-9 Advanced True IDE Multiword DMA Mode Selected Indicates the current True IDE Multiword DMA mode selected on the card Value ...
Page 30
... Features 66H and CCH can be used to enable and disable whether the Power-on Reset (POR) Defaults will be set when a software reset occurs. ©2010 Greenliant Systems, Ltd. NAND Controller -D data bus and the IOCS16# signal will not be asserted for GLS55VD020 T0-0.0 1355 S71355-05-000 05/10 ...
Page 31
... NAND Controller GLS55VD020 TABLE 10: Transfer Mode Values Mode PIO default mode PIO default mode, disable IORDY PIO flow control transfer mode Multi-word DMA mode Ultra-DMA mode Reserved 1. Mode = transfer mode number, all other values are not valid Idle - 97H or E3H Bit -> ...
Page 32
... NAND Controller GLS55VD020 Status Register RDY DWF DSC CORR ERR ...
Page 33
... NAND Controller GLS55VD020 TABLE 11: Error and Status Register Command BBK Security-Erase-Prepare Security-Erase-Unit Security-Freeze-Lock Security-Set-Password Security-Unlock Seek Set-Features Set-Multiple-Mode Set-Sleep-Mode Set-WP#/PD#-Mode SMART Standby Standby-Immediate Translate-Sector Write-Buffer Write-DMA Write-Multiple Write-Multiple-Without-Erase Write-Sector(s) Write-Sector(s)-Without-Erase Write-Verify Invalid-Command-Code 1.The host is required to reissue any media access command (such as Read-Sector and Write Sector) that ends with an error condition. ...
Page 34
... Min Max Min 2.7V 3.465V 3.135V 2.7V 3.465V 3.135V = 100 pF for 3. for 100 pF for 3.3V and 5. for NAND Controller GLS55VD020 V DD +2. DDQ +2.0V V DDQ Conditions -0.3V min to 6.5V max -0.3V min to 4.0V max -0.5V min 0.5V max DD -0.5V min 0.5V max DDQ T0-0.0 1355 ...
Page 35
... NAND Controller GLS55VD020 TABLE 13: Recommended System Power-on Timing Symbol Parameter T Drive Initialization to Ready PU-INITIAL 1 T Host Power-on/Reset to Ready Operation PU-READY1 1 T Host Power-on/Reset to Write Operation PU-WRITE1 1. This parameter is measured only for initial qualification and after a design or process change that could affect this parameter. ...
Page 36
... Greenliant Systems, Ltd. NAND Controller = 3.0V DD Min Max Units 2.0 V 0.8 - -160 -10 uA 2.0 V 0.8 - 2.2 V 0.4 -1.2 mA 1.2 mA 2 GLS55VD020 Conditions V =V Max Min GND Max GND Max Max Min ...
Page 37
... NAND Controller GLS55VD020 TABLE 18: DC Characteristics for Host Interface V Symbol Type Parameter V Input Voltage IH1 I1 V IL1 I I1Z Input Leakage Current IL1 I I1U Input Pull-Up Current U1 V Input Voltage Schmitt Trigger T T-2 I I2Z Input Leakage Current IL2 I I2U Input Pull-Up Current ...
Page 38
... Min Max = 0°C to +70° -40°C to +85°C) 100 A = 0°C to +70°C) 700 A = -40°C to +85°C) 950 A 38 NAND Controller GLS55VD020 Units Conditions Max DDQ DDQ V =V Min DDQ DDQ GND DDQ Max ...
Page 39
... V IHT INPUT V ILT AC test inputs are driven at V IHT points for inputs and outputs are V FIGURE 5: AC Input/Output Reference Waveforms Media Side Interface Timing Specifications TABLE 21: GLS55VD020 Timing Specifications Symbol Parameter T FCLE Setup Time CLS T FCLE Hold Time CLH T FCE# Setup Time ...
Page 40
... ALS ALH Command BYTE1 BYTE2 40 NAND Controller GLS55VD020 1355 F09 ALH BYTE3 BYTE4 1355 F10.0 S71355-05-000 T DH 05/10 ...
Page 41
... NAND Controller GLS55VD020 FCLE FCE# FALE FWE# FAD[15:0] or FAD[7:0] FIGURE 8: Media Data Loading Latch Cycle FCE# FRE# FAD[15:0] or FAD[7: FRBYbsy# FIGURE 9: Media Data Read Cycle ©2010 Greenliant Systems, Ltd ...
Page 42
... XX XX XXX - XX Valid Combinations Valid combinations for GLS55VD020 GLS55VD020-60-C-TQWE GLS55VD020-60-I-TQWE Note: Valid combinations are those products in mass production or will be in mass production. Consult your Greenliant sales representative to confirm availability of valid combinations and to determine availability of new combinations. ©2010 Greenliant Systems, Ltd. ...
Page 43
... NAND Controller GLS55VD020 PACKAGING DIAGRAM TOP VIEW Pin #1 Identifier 14.00 BSC 16.00 BSC FIGURE 10: 100-lead Thin Quad Flat Pack (TQFP) Greenliant Package Code: TQW ©2010 Greenliant Systems, Ltd. 0.17 0.27 14.00 BSC 16.00 0.50 BSC BSC .95 1.05 .09 .20 NOTE: 1. Complies with JEDEC publication 95 MS-026 variant AED dimensions although some dimensions may be more stringent. ...
Page 44
... FIGURE 11: 85-ball Very-Thin, Fine-Pitch, Ball Grid Array (VFBGA) Greenliant Package Code: MVW ©2010 Greenliant Systems, Ltd. BOTTOM VIEW 4.50 6.00 ±0.08 4.50 0. 0.86 ± 0.10 SIDE VIEW 0.075 0.20 ± 0.06 44 NAND Controller GLS55VD020 0.32 ±0.05 0.50 (85X INDICATOR 1mm 85-vfbga-MVW-6x6-32mic-0 ...
Page 45
... NAND Controller GLS55VD020 TABLE 22: Revision History Number 00 • Initial Release of Data Sheet • Updated “Features:” and “Product Description” 01 • Modified “General Description” on page 3. • Updated Table 2 on page 11 • Modified “Manufacturing Support”and “Security Features”on page 12 • ...