AT27C010-70P Atmel, AT27C010-70P Datasheet
AT27C010-70P
Specifications of AT27C010-70P
Available stocks
Related parts for AT27C010-70P
AT27C010-70P Summary of contents
Page 1
... PDIP and PLCC packages. All devices feature two-line control (CE, OE) to give designers the flexibility to prevent bus contention. With 128K byte storage capability, the AT27C010 allows firmware to be stored reliably and to be accessed by the system without the delays of mass storage media. ...
Page 2
... Additionally, to stabilize the supply voltage level on printed circuit boards with large EPROM arrays, a 4.7µF bulk electrolytic capacitor should be utilized, again connected between the V close as possible to the point where the power supply is connected to the array. Figure 3-1. Block diagram Atmel AT27C010 2 32-lead PLCC Top view A7 ...
Page 3
... ( Identification code A16 = and A0, which is toggled low H Atmel AT27C010 -70 -40C - 85C 5V 10% Outputs D OUT High Z High OUT High Z 3 ...
Page 4
... CE without impact after the address is valid without impact on t ACC OE Min Max Ind. Ind. + 0.5V IL -0 Atmel AT27C010 -45 -70 Min Max Min 0.0V and V = 3.0V. Timing measure 2.0V. Input AC drive levels are V = 0.45V and ...
Page 5
... L Table 5-5. Pin capacitance ( 1MHz 25°C Symbol Typ OUT Note: 1. Typical values for nominal supply voltage. This parameter is only sampled, and is not 100% tested. 0321N–EPROM–4/11 Max Units Atmel AT27C010 Conditions OUT 5 ...
Page 6
... Figure 5-4. Programming Waveforms Notes: 1. The input timing reference is 0.8V for and t are characteristics of the device, but must be accommodated by the programmer. OE DFP 3. When programming the Atmel AT27C010, a 0.1µF capacitor is required across V age transients. Atmel AT27C010 6 (1) and 2.0V for and ground to suppress spurious volt- PP 0321N– ...
Page 7
... This parameter is only sampled, and is not 100% tested. Output float is defined as the point where data is no longer driven. See timing diagram. 3. Program pulse width tolerance is 100µsec±5%. Table 5-8. The Atmel AT27C010 integrated product identification code Codes Manufacturer Device type 0321N– ...
Page 8
... After the byte verifies properly, the next address is selected until all have been checked then lowered to 5.0V and V PP determine if the device passes or fails. Figure 6-1. Rapid programming algorithm Atmel AT27C010 8 to 5.0V. All bytes are read again and compared with the original data raised to 6.5V and V is raised CC PP 0321N– ...
Page 9
... J-leaded chip carrier (PLCC) 32P6 32-lead, 0.600" wide, plastic, dual inline package (PDIP) 0321N–EPROM–4/11 Standby Atmel ordering code 0.1 AT27C010-45JU AT27C010-70JU 0.1 AT27C010-70PU Package type Atmel AT27C010 Package Lead finish Operation range 32J Matte tin (-40C to 85C) 32J ...
Page 10
... Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is .010"(0.254mm) per side. Dimension D1 and E1 include mold mismatch and are measured at the extreme material condition at the upper or lower parting line. 3. Lead coplanarity is 0.004" (0.10mm) maximum. Package Drawing Contact: packagedrawings@atmel.com Atmel AT27C010 10 1.14(0.045) X 45° PIN NO. 1 IDENTIFIER E1 E ...
Page 11
... Package Drawing Contact: packagedrawings@atmel.com 0321N–EPROM–4/11 D PIN 0º ~ 15º REF eB TITLE 32P6, 32-lead (0.600"/15.24mm wide) Plastic Dual Inline Package (PDIP) Atmel AT27C010 COMMON DIMENSIONS (Unit of Measure = mm) MIN NOM MAX NOTE SYMBOL A – – 4.826 A1 0.381 – – D 41.783 – ...
Page 12
... Revision history Doc. Rev. Date Comments 0321N 04/2011 Remove TSOP package Add lead finish to ordering information 0321M 12/2007 Atmel AT27C010 12 0321N–EPROM–4/11 ...
Page 13
... Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT ...