CM05Y5V104Z16AH AVX, CM05Y5V104Z16AH Datasheet - Page 11

• Manufacturer Part Number: CM05Y5V104Z16AH
• Description: CAPACITOR, 0402, 100NF, 16V; Application: Standard; Capacitance: 100000pF; Tolerance, Capacitance: +80%, -20%; Series...
• Manufacturer: AVX

Test conditions and Specification for High Dielectric Type (X5R, X7R, Y5V)
*1
*2
*3
*4
*5
*6
*7
*8
*9
Capacitance Value
tan (%)
Insulation resistance (IR)
Dielectric Resistance
Appearance
Termination strength
Bending strength test
Vibration
test
Soldering
heat
resistance
Solderability
Temperature
cycle
Humidity
test
High-
temperature
with
loading
Use 1.5 times when the rated voltage is 250V or over.
Use 1.2 times when the rated voltage is 630V or over.
Apply to X5R 35V type, X7R 16V/25V type.
Apply to X5R16V/25V type, X7R/X7S 6.3V/10V type.
Apply to Y5V 16V type, CM32Y5V335 to 106 (25V Type).
Apply to Y5V 6.3V/10V type. Apply 16% to CM21Y5V106/CM316Y5V226.
Exclude CT series with thickness of less than 0.66mm and CA series.
Different Specification for Nickel Barrier termination DN/DR series. (Alumina Substrate)
Keep specimen at 150 C 0/ 10 C for one hour, leave specimen at room ambient for 48 4 hours.
Apply the same test condition for one hour, then leave the specimen at room ambient for 48 4 hours.
( 7)
( 11)
Test Items
Appearance
tan (%)
Appearance
tan (%)
IR
Withstand voltage
Appearance
tan (%)
IR
Withstand voltage
Appearance
tan (%)
IR
Appearance
tan (%)
IR
C
C
C
C
C
( 15)
( 15)
( 15)
( 15)
( 15)
( 6)
( 6)
( 15)
( 15)
( 15)
2.5%max, 3.5%max
Within tolerance
10,000M or 500M • F min, whichever is less
No problem observed
No problem observed
No problem observed
No problem observed at 1mm bent
No significant change is detected.
Within tolerance
Satisfies the initial value.
No significant change is detected.
Satisfies the initial value.
10,000M or 500M • F min, whichever is smaller
Resists without problem
Ni/Br termination: 90% min
No significant change is detected.
Satisfies the initial value.
10,000M or 500M • F min, whichever is smaller
Resists without problem
No significant change is detected.
500M or 25M • F min, whichever is smaller
No significant change is detected.
1,000M or 50M • F min, whichever is smaller
5.0%max
Within 12.5%
Within 12.5%
Within 7.5%
Within 7.5%
200% max of
200% max of
initial value
initial value
X7R/X5R
( 3), 7.5%max ( 17)
( 2)
,
7.0%
max
Specification
( 12)
9.0% max
5.0%max, 7.0%max
*10 For the CF series over 1000V, apply 500V for 1 minutes at room ambient.
*11 Except CF series.
*12 Apply to X5R 10V type, X7S 4V type.
*13 Apply to 25V series of CM105Y5V154 over, CM21Y5V105 over, 316Y5V155 over.
*14 Measurement condition 1kHz, 1Vrms for Y5V, C < 47 F type.
*15 The charge/discharge current of the capacitor must not exceed 50mA.
*16 2N at 0201 Size
*17 Apply to X5R 4V and 6.3V type.
*18 Use 1.5times when the rated voltage is 4V/6.3V/10V/250V and 100V (32X7R474/43X7R105/55X7R105).
150% max of
150% max of
Within 20%
Within 20%
Within 30%
Within 30%
initial value
initial value
Use 1.2times when the rated voltage is 630V or over.
( 4)
Y5V
,
initial value
12.5%max
Multilayer Ceramic Chip Capacitors
( 13)
( 5)
Test Conditions and Standards
Do previous treatment
Microscope(10 magnification)
Soaking Condition
Measured after the rated voltage is applied for 2minutes
at normal room temperature and humidity. ( 10)
( 1) Apply 2.5 times of the rated voltage for 1 to 5 seconds.
Apply a sideward force of 500g(5N) ( 16) to a
PCB-mounted sample.
Glass epoxy PCB (t=1.6mm); fulcrum
Spacing: 90mm; for 10 seconds.
Vibration frequency: 10 to 55(Hz)
Amplitude: 1.5mm
Sweeping condition: 10 55 10Hz/min
In X, Y and Z directions:
2 hours each Total 6 hours
Do previous treatment
Soak the sample in 260 C 5 C
solder for 10 0.5seconds
and place in a room at normal temperature
and humidity; measure after 48 4hours.
(Preheating Conditions)
Do previous treatment
(Cycle)
Normal room temperature (3min)
Lowest operation temperature (30min)
Normal room temperature (3min)
Highest operation temperature (30min)
After five cycles
48 4hours.
Do previous treatment
After storing it at a temperature of
40 C 2 C and a relative humidity of
90-95% for 500 24/ 0hours, measure
the sample after storing 48 4hours.
Do previous treatment
After applying twice
voltage at the highest operating temperature
for 1000 48/ 0hours, measure the sample
after storing 48 4hours.
Sn63 Solder
Sn-3Ag-0.5Cu
Capacitance
Order
C 10 F
C>10 F
1
2
Test Condition
Temperature
150 to 200 C
80 to 100 C
120Hz 10% 0.5 0.1Vrms
( 7)
1kHz 10% 1.0 0.1Vrms
235 5 C
245 5 C
, measure after
( 18)
Fire
( 8, 14)
( 8)
( 8)
( 9)
( 9)
of the rated
2 0.5sec.
3 0.5sec.
2minutes
2minutes
Vol
Time