HTS10-P LEM [LEM], HTS10-P Datasheet

HTS10-P

Manufacturer Part Number

HTS10-P

Description

Current Transducer

Manufacturer

LEM [LEM]

Datasheet

1.HTS10-P.pdf (2 pages)

Current page: 1 of 2
Download datasheet (199Kb)

The HTS 10-P provides electronic measurement of AC,

DC, pulsed, and complex currents with galvanic

isolation between the primary (power) circuit and the

secondary (measurement) circuit.

Electrical Data

Accuracy-Dynamic Performances

General Data

Notes:

1) This device is ratiometric: sensitivity and offset vary in direct proportion to supply voltage.

2) Output linearity is not guaranteed within 500mV of the supply rails.

3) Output loading to V

LEM U.S.A., INC.

6643 WEST MILL ROAD

MILWAUKEE, WI 53218

Nominal Current

Measurement Range

Sensitivity

Overload Capacity

Supply Voltage (note 1)

Primary to Secondary Isolation

Maximum Output (note 2)

Zero Offset

Linearity

Zero Offset Drift

Magnetic Offset

Gain Drift

Bandwidth, typical

Response Time, typical

Operating Temperature

Storage Temperature

Current Consumption

Output Current (note 3)

Enclosure and Potting

Weight

Fastening

Output Reference

HTS 10-P Current Transducer

LEM reserves the right to carry out modifications on its transducers without prior notice.

25°C

25°C (note 1)

or V

TEL: 414/ 353-0711

FAX: 414/ 353-0733

must be = 5.1k . Tested with 10k from O

Page 1 of 2

10 A

± 15 A

± 25 A for 15 seconds

5.0 V

2500 V

within 500 mV of each supply rail = 0.5 to 4.5 V

< 0.8% typical, 1.2% maximum

± 2.0 mV/K maximum

± 0.5 % after 45A peak overload

± 0.20 %/K maximum

DC - 16 kHz (-3dB; 10 kHz @ -1dB)

25 µs (with 2 - 10 A/µs rising or falling edge)

-40 to 85 °C

-55 to 95 °C

12 mA max

1 mA source and sink

UL Recognized materials meeting UL94-V0

5 grams nominal

PCB Footprint (as shown on page 2)

A positive going output signal is obtained when

the primary current flows from the I+ to I- pin.

• 20 = 100 mV/A ± 30%

/ 2 = 2.5 V

RMS

± 10%

for 1 minute

5.5V

± 12%

http://www.lem.com

to V

lus@lem.com

030516/01

C:\aaa\Projects\HTS10P\Rev 01\HTS10P(01).doc 03.05.16 18:11

Related parts for HTS10-P

HTS10-P Summary of contents

Page 1

... PCB Footprint (as shown on page 2) A positive going output signal is obtained when the primary current flows from the pin. must be = 5.1k . Tested with 10k from O Page TEL: 414/ 353-0711 FAX: 414/ 353-0733 ± 12 030516/01 lus@lem.com http://www.lem.com C:\aaa\Projects\HTS10P\Rev 01\HTS10P(01).doc 03.05.16 18:11 ...

Page 2

... LEM reserves the right to carry out modifications on its transducers without prior notice. LEM U.S.A., INC. 6643 WEST MILL ROAD MILWAUKEE, WI 53218 (1mm = 0.0394”) , placed as close to the HTS 10-P pins as possible. Page TEL: 414/ 353-0711 FAX: 414/ 353-0733 : and V and a 100pF DD SS 030516/01 lus@lem.com http://www.lem.com C:\aaa\Projects\HTS10P\Rev 01\HTS10P(01).doc 03.05.16 18:11 ...

Related keywords

HTS10-P datasheet
HTS10-P data sheet
HTS10-P pdf datasheet
HTS10-P component
HTS10-P part
HTS10-P distributor
HTS10-P RoHS
HTS10-P datasheet download