AM42-0007_V8 MA-COM [M/A-COM Technology Solutions, Inc.], AM42-0007_V8 Datasheet - Page 2

• Manufacturer Part Number: AM42-0007_V8
• Description: GaAs MMIC VSAT Power Amplifier, 2.0 W
• Manufacturer: MA-COM [M/A-COM Technology Solutions, Inc.]

2
Absolute Maximum Ratings
ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions
is considering for development. Performance is based on target specifications, simulated results,
and/or prototype measurements. Commitment to develop is not guaranteed.
PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology
Solutions has under development. Performance is based on engineering tests. Specifications are
typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available.
Commitment to produce in volume is not guaranteed.
GaAs MMIC VSAT Power Amplifier, 2.0 W
14.0 - 14.5 GHz
Electrical Specifications: T
1. Exceeding any one or combination of these limits may cause
2. M/A-COM Technology does not recommend sustained
3. Case Temperature (T
AM42-0007
Saturated Output Power
Detector Output Voltage
Power Added Efficiency
permanent damage to this device.
operation near these survivability limits.
Output Power at P1dB
Channel Temperature
Storage Temperature
Thermal Resistance
Power Dissipation
RF Input Power
Output VSWR
Input VSWR
Bias Current
Parameter
Linear Gain
Parameter
Output IP3
V
V
I
DS
GG
DD
C
) = +25°C.
Two +24 dB, output tones @ 1 MHz spacing
Absolute Maximum
-65°C to +150°C
R
A
+23 dBm
2100 mA
-10 Volts
12 Volts
L
1,2,3
13.2 W
150°C
= +25°C, V
= 10 K Ω, P
Test Conditions
25°C Heat Sink
P
P
P
P
P
IN
IN
I
I
DD
GG
IN
IN
IN
= +14 dBm
= +14 dBm
< 0 dBm
< 0 dBm
< 0 dBm
(No RF)
(No RF)
—
OUT
DD
= +31dBm
= +9 V, V
M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make
changes to the product(s) or information contained herein without notice.
Typical Bias Configuration
4. Nominal bias is obtained by first connecting –5 volts to pin 4
5. RF ground and thermal interface is the flange (case bottom).
6. No DC bias voltage appears at the RF ports.
7. For optimum IP3 performance, the V
8. Resistor and capacitors surrounding the amplifier are
• North America Tel: [phone] • Europe Tel: [phone]
• India Tel: [phone]
Visit www.macomtech.com for additional data sheets and product information.
(V
sequence.
Adequate heat sinking is required.
should be placed within 0.5 inches of pin 6.
suggestions and not included as part of the AM42-0007.
GG
GG
), followed by connection +9 volts to pin 6 (V
=- 5.0 V, Z
RF In
3
Units
Ratio
Ratio
°C/W
dBm
dBm
dBm
10 K Ω
mA
mA
dB
1,2,5,9,10
%
V
GND
V
7
DET
AM42-0007
0
= 50 Ω
Min.
19
31
—
—
—
—
—
—
—
—
—
0.01 µF
V
3.3 µF
• China Tel: [phone]
0.01 µF
GG
4
V
DD
6
DD
Typ.
2.5:1
2.7:1
4,5,6,7,8
bypass capacitors
+3.5
850
9.5
22
33
32
41
22
18
RF Out
8
DD
). Note
Max.
2.7:1
Rev. V8
—
—
—
—
—
—
—
25
—
—