MM74HC4538N Fairchild Semiconductor, MM74HC4538N Datasheet - Page 3

• Manufacturer Part Number: MM74HC4538N
• Description: IC MULTIVIBRATOR MONO DL 16-DIP
• Manufacturer: Fairchild Semiconductor
• Series: 74HCr

Specifications of MM74HC4538N

• Logic Type: Monostable
• Independent Circuits: 2
• Schmitt Trigger Input: Yes
• Propagation Delay: 26ns
• Current - Output High, Low: 5.2mA, 5.2mA
• Voltage - Supply: 2 V ~ 6 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Through Hole
• Package / Case: 16-DIP (0.300", 7.62mm)
• Elements Per Chip: 2
• Logic Family: HC
• Input Bias Current (max): 130 mA
• Propagation Delay Time: 275 ns, 55 ns, 47 ns
• High Level Output Current: - 5.2 mA
• Low Level Output Current: 5.2 mA
• Supply Voltage (max): 6 V
• Supply Voltage (min): 2 V
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: Through Hole
• Operating Supply Voltage: 2.5 V, 3.3 V, 5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 74HC4538

Timing Diagram
Circuit Operation
The MM74HC4538 operates as follows (refer to logic dia-
gram). In the quiescent state, the external timing capacitor,
C
goes HIGH and C
ence voltage (V
through R
Upper
and the Q output goes LOW.
The following, more detailed description of the circuit oper-
ation refers to both the logic diagram and the timing dia-
gram.
QUIESCENT STATE
In the quiescent state, before an input trigger appears, the
output latch is HIGH and the reset latch is HIGH (#1 in logic
diagram).
Thus the Q output (pin 6 or 10) of the monostable multivi-
brator is LOW (#2, timing diagram).
The output of the trigger-control circuit is LOW (#3), and
transistors M1, M2, and M3 are turned off. The external
timing capacitor, C
reference circuit has a LOW output (#5). Transistor M4 is
turned ON and transmission gate T1 is turned OFF. Thus
the lower reference circuit has V
input and a resulting LOW output (#6).
In addition, the output of the trigger-control reset circuit is
LOW.
X
, is charged to V
2
/
X
3
, back up to the upper reference voltage (V
V
CC
), at which point the one-shot has timed out
REF
X
X
CC
, is charged to V
discharges quickly to the lower refer-
Lower
. When a trigger occurs, the Q output
1
/
3
V
CC
CC
CC
). C
at the noninverting
(#4), and the upper
X
then charges,
REF
3
TRIGGER OPERATION
The MM74HC4538 is triggered by either a rising-edge sig-
nal at input A (#7) or a falling-edge signal at input B (#8),
with the unused trigger input and the Reset input held at
the voltage levels shown in the Truth Table. Either trigger
signal will cause the output of the trigger-control circuit to
go HIGH (#9).
The trigger-control circuit going HIGH simultaneously ini-
tiates three events. First, the output latch goes LOW, thus
taking the Q output of the HC4538 to a HIGH State (#10).
Second, transistor M3 is turned on, which allows the exter-
nal timing capacitor, C
ground (#11). (Note that the voltage across C
the input of the upper reference circuit comparator.) Third,
transistor M4 is turned off and transmission gate T1 is
turned ON, thus allowing the voltage across C
appear at the input of the lower reference circuit compara-
tor.
When C
reference circuit (#12), the outputs of both reference cir-
cuits will be HIGH (#13). The trigger-control reset circuit
goes HIGH, resetting the trigger-control circuit flip-flop to a
LOW State (#14). This turns transistor M3 OFF again,
allowing C
time constant t
turned ON and transmission gate T1 is turned OFF. Thus a
high voltage level is applied to the input of the lower refer-
ence circuit comparator, causing its output to go LOW
(#16). The monostable multivibrator may be retriggered at
any time after the trigger-control circuit goes LOW.
When C
reference circuit (#17), the output of the upper reference
circuit goes LOW (#18). This causes the output latch to
X
X
charges up to the reference voltage of the upper
discharges to the reference voltage of the lower
X
to begin to charge back up toward V
R
X
C
X
(#15). In addition, transistor M4 is
X
, to rapidly discharge toward
www.fairchildsemi.com
X
appears at
CC
X
, with a
to also