ML4827CP-1 Micro Linear, ML4827CP-1 Datasheet - Page 12

no-image

ML4827CP-1

Manufacturer Part Number
ML4827CP-1
Description
Fault-Protected PFC and PWM Controller Combo
Manufacturer
Micro Linear
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ML4827CP-1
Manufacturer:
ML
Quantity:
20 000
ML4827
FUNCTIONAL DESCRIPTION
FUNCTIONAL DESCRIPTION
Using the recommended values of
= 64% for a high- application, a MOSFET switch with a
Drain-Source breakdown voltage of 900V, or in some
cases as low as 800V, can reliably be used. Such parts are
readily and inexpensively available from a number of
vendors.
V
The V
PFC and inhibits the PWM if this voltage on V
than its nominal 2.5V. Once this voltage reaches 2.5V,
which corresponds to the PFC output capacitor being
charged to its rated boost voltage, the soft-start begins.
PWM Control (RAMP 2)
When the PWM section is used in current mode, RAMP 2
is generally used as the sampling point for a voltage
representing the current in the primary of the PWM’s
output transformer, derived either by a current sensing
resistor or a current transformer. In voltage mode, it is the
input for a ramp voltage generated by a second set of
timing components (R
minimum value of zero volts and should have a peak
value of approximately 5V. In voltage mode operation,
feedforward from the PFC output buss is an excellent way
to derive the timing ramp for the PWM stage.
Soft Start
Start-up of the PWM is controlled by the selection of the
external capacitor at SS. A current source of 50µA
supplies the charging current for the capacitor, and start-
up of the PWM begins at 1.25V. Start-up delay can be
programmed by the following equation:
where C
t
12
DELAY
IN
OK Comparator
C
IN
SS
is the desired start-up delay.
OK comparator monitors the DC output of the
SS
t
is the required soft start capacitance, and
DELAY
50
125
.
RAMP2
A
V
, C
RAMP2
Figure 4. External Component Connections to V
MIN
), which will have a
= 60% and
(Continued)
(Continued)
FB
ML4827
V BIAS
GND
V CC
is less
R BIAS
MAX
(6)
CERAMIC
10nF
It is important that the time constant of the PWM soft-start
allow the PFC time to generate sufficient output power for
the PWM section. The PWM start-up delay should be at
least 5ms.
Solving for the minimum value of C
Generating V
The ML4827 is a current-fed part. It has an internal shunt
voltage regulator, which is designed to regulate the
voltage internal to the part at 13.5V. This allows a low
power dissipation while at the same time delivering 10V
of gate drive at the PWM OUT and PFC OUT outputs. It is
important to limit the current through the part to avoid
overheating or destroying it. This can be easily done with
a single resistor in series with the V
bias supply of typically 18V to 20V. The resistor’s value
must be chosen to meet the operating current requirement
of the ML4827 itself (19mA max) plus the current required
by the two gate driver outputs.
EXAMPLE:
With a V
ML4827 driving a total gate charge of 110nC at 100kHz
(e.g., 1 IRF840 MOSFET and 2 IRF830 MOSFETs), the
gate driver current required is:
To check the maximum dissipation in the ML4827, find
the current at the minimum V
The maximum allowable I
acceptable design.
I
R
I
C
GATEDRIVE
CC
BIAS
SS
CERAMIC
BIAS
1µF
20
5
ms
19
V
20
180
CC
of 20V, a V
mA
V
100
50
12 4
125
.
.
14 6
kHz
11
CC
A
V
V
.
mA
V
CC
220
42 2
100
CC
.
limit of 14.6V (max) and the
180
nF
mA
is 55mA, so this is an
CC
nC
(12.4V):
11
CC
SS
mA
:
pin, returned to a
(7)
(8)
(9)

Related parts for ML4827CP-1