ML4804CS Micro Linear, ML4804CS Datasheet - Page 8

no-image

ML4804CS

Manufacturer Part Number
ML4804CS
Description
Power Factor Correction and PWM Controller Combo
Manufacturer
Micro Linear
Datasheet
ML4804
The output of the gain modulator is a current signal, in the
form of a full wave rectified sinusoid at twice the line
frequency. This current is applied to the virtual-ground
(negative) input of the current error amplifier. In this way
the gain modulator forms the reference for the current
error loop, and ultimately controls the instantaneous
current draw of the PFC from the power line. The general
form for the output of the gain modulator is:
More exactly, the output current of the gain modulator is
given by:
where K is in units of V
Note that the output current of the gain modulator is
limited to 500µA.
Current Error Amplifier
The current error amplifier’s output controls the PFC duty
cycle to keep the average current through the boost
inductor a linear function of the line voltage. At the
inverting input to the current error amplifier, the output
current of the gain modulator is summed with a current
which results from a negative voltage being impressed
upon the I
represents the sum of all currents flowing in the PFC
circuit, and is typically derived from a current sense
resistor in series with the negative terminal of the input
bridge rectifier. In higher power applications, two current
transformers are sometimes used, one to monitor the I
the boost MOSFET(s) and one to monitor the I
8
FUNCTIONAL DESCRIPTION
15
2
4
3
7
I AC
V FB
V RMS
I SENSE
RAMP 1
2.5V
SENSE
+
VEA
VEAO
pin. The negative voltage on I
MODULATOR
GAIN
16
-1
.
1.6k
1.6k
+
IEA
IEAO
Figure 1. PFC Section Block Diagram
1
OSCILLATOR
(Continued)
F
0.5V
SENSE
of the
+
16.4V
V CC
+
D
(1)
TRI-FAULT
of
+
V CC OVP
boost diode. As stated above, the inverting input of the
current error amplifier is a virtual ground. Given this fact,
and the arrangement of the duty cycle modulator
polarities internal to the PFC, an increase in positive
current from the gain modulator will cause the output
stage to increase its duty cycle until the voltage on
I
current. Similarly, if the gain modulator’s output
decreases, the output duty cycle will decrease, to
achieve a less negative voltage on the I
Cycle-By-Cycle Current Limiter
The I
feedback loop, is a direct input to the cycle-by-cycle
current limiter for the PFC section. Should the input
voltage at this pin ever be more negative than -1V, the
output of the PFC will be disabled until the protection
flip-flop is reset by the clock pulse at the start of the next
PFC power cycle.
TriFault Detect
To improve power supply reliability, reduce system
component count, and simplify compliance to UL 1950
safety standards, the ML4800 (ML4804) includes TriFault
Detect. This feature monitors VFB (Pin 15) for certain PFC
fault conditions.
In the case of a feedback path failure, the output of the
PFC could go out of safe operating limits. With such a
failure, VFB will go outside of its normal operating area.
Should VFB go too low, too high, or open, TriFault Detect
senses the error and terminates the PFC output drive.
TriFault detect is an entirely internal circuit. It requires no
external components to serve its protective function.
SENSE
2.75V
SENSE
–1V
is adequately negative to cancel this increased
PFC I LIMIT
pin, as well as being a part of the current
OVP
+
+
TM
S
R
S
R
Q
Q
Q
Q
SENSE
PFC OUT
pin.
12

Related parts for ML4804CS