HIP6013 Intersil Corporation, HIP6013 Datasheet - Page 5

• Manufacturer Part Number: HIP6013
• Description: Buck Pulse-Width Modulator (PWM) Controller
• Manufacturer: Intersil Corporation

Functional Description
Initialization
The HIP6013 automatically initializes upon receipt of power.
Special sequencing of the input supplies is not necessary.
The Power-On Reset (POR) function continually monitors
the input supply voltages and the enable (EN) pin. The POR
monitors the bias voltage at the VCC pin and the input
voltage (V
equal to V
protection). With the EN pin held to VCC, the POR function
initiates soft start operation after both input supply voltages
exceed their POR thresholds. For operation with a single
+12V power source, V
+12V power source must exceed the rising V
before POR initiates operation.
The Power-On Reset (POR) function inhibits operation with
the chip disabled (EN pin low). With both input supplies
above their POR thresholds, transitioning the EN pin high
initiates a soft start interval.
Soft Start
The POR function initiates the soft start sequence. An
internal 10 A current source charges an external capacitor
(C
amplifier output (COMP pin) and reference input (+ terminal
of error amp) to the SS pin voltage. Figure 3 shows the soft
start interval with C
error amplifier (COMP pin) controls the converter’s output
voltage. At t1 in Figure 3, the SS voltage reaches the valley
of the oscillator’s triangle wave. The oscillator’s triangular
waveform is compared to the ramping error amplifier voltage.
This generates PHASE pulses of increasing width that
charge the output capacitor(s). This interval of increasing
pulse width continues to t2. With sufficient output voltage,
the clamp on the reference input controls the output voltage.
This is the interval between t2 and t3 in Figure 3. At t3 the
SS voltage exceeds the reference voltage and the output
voltage is in regulation. This method provides a rapid and
controlled output voltage rise.
SS
) on the SS pin to 4V. Soft start clamps the error
IN
IN
) on the OCSET pin. The level on OCSET is
less a fixed voltage drop (see over-current
SS
IN
= 0.1 F. Initially the clamp on the
and V
2-166
CC
are equivalent and the
CC
threshold
HIP6013
Over-Current Protection
The over-current function protects the converter from a
shorted output by using the upper MOSFET’s on-resistance,
r
converter’s efficiency and reduces cost by eliminating a
current sensing resistor.
The over-current function cycles the soft-start function in a
hiccup mode to provide fault protection. A resistor (R
programs the over-current trip level. An internal 200 A
(typical) current sink develops a voltage across R
is reference to V
MOSFET (also referenced to V
across R
start sequence. The soft-start function discharges C
a 10 A current sink and inhibits PWM operation. The soft-
start function recharges C
with the error amplifier clamped to the SS voltage. Should an
overload occur while recharging C
inhibits PWM operation while fully charging C
complete its cycle. Figure 4 shows this operation with an
overload condition. Note that the inductor current increases
to over 15A during the C
over-current trip. The converter dissipates very little power
with this method. The measured input power for the
conditions of Figure 4 is 2.5W.
DS(ON)
0V
0V
to monitor the current. This method enhances the
OCSET
FIGURE 3. SOFT-START INTERVAL
, the over-current function initiates a soft-
IN
SOFT-START
(1V/DIV)
. When the voltage across the upper
t1
SS
TIME (5ms/DIV)
SS
charging interval and causes an
, and PWM operation resumes
IN
t2
) exceeds the voltage
SS
OUTPUT
VOLTAGE
(1V/DIV)
, the soft start function
t3
SS
OCSET
to 4V to
OCSET
SS
with
that
)