NCV8460A ONSEMI [ON Semiconductor], NCV8460A Datasheet
NCV8460A
Available stocks
Related parts for NCV8460A
NCV8460A Summary of contents
Page 1
... Self Protected High Side Driver with Temperature Shutdown and Current Limit The NCV8460A is a fully protected High−Side driver that can be used to switch a wide variety of loads, such as bulbs, solenoids and other acuators. The device is internally protected from an overload condition by an active current limit and thermal shutdown. ...
Page 2
Input IN Buffer STAT GND PIN DESCRIPTION Pin # Symbol 1 GND Ground 2 IN Logic Level Input 3 STAT Status Output 4 N/C No Connection 5 V Supply Voltage D 6 OUT Output 7 OUT Output 8 V Supply ...
Page 3
MAXIMUM RATINGS Rating DC Supply Voltage Peak Transient Input Voltage (Load Dump 51 13.5 V, ISO7637−2 pulse 5) D Input Voltage Input Current Output Current (Note 1) Negative Ground Current Status Current Power Dissipation 25°C ...
Page 4
ELECTRICAL CHARACTERISTICS Rating Symbol Operating Supply Voltage V D Undervoltage Shutdown V UV Undervoltage V UV_Rst Overvoltage Shutdown Resistance R ON Standby Current I D Output Leakage Current I L INPUT CHARACTERISTICS Input Voltage − Low V ...
Page 5
ELECTRICAL CHARACTERISTICS Rating Rating Symbol Symbol DIAGNOSTICS CHARACTERISTICS Openload On State Detection I OL1 Threshold Openload On State Detection I OL2 Threshold Openload On State Detection t d_OL_on Delay Openload Off State Detection V OL Threshold Openload Detection Delay at ...
Page 6
STATUS PIN TRUTH TABLE Conditions Normal Operation Undervoltage Overvoltage Current Limitation Overtemperature Output Voltage > Output Current < Input Output ...
Page 7
TYPICAL CHARACTERISTICS CURVES 5.6 5.4 5.2 5.0 4.8 4.6 4.4 4.2 − TEMPERATURE (°C) Figure 5. Undervoltage Shutdown vs. Temperature 148 128 150°C 108 88 68 25°C 48 −40° (V) ...
Page 8
TYPICAL CHARACTERISTICS CURVES 4 3.5 3 2.5 2 1.5 1 − TEMPERATURE (°C) Figure 11. V Threshold Low vs. Temperature in 14 13.5 13 12.5 12 11.5 11 10.5 10 − TEMPERATURE (°C) Figure 13. Input ...
Page 9
TYPICAL CHARACTERISTICS CURVES 0.70 0.60 25°C 0.50 0.40 0.30 −40°C 150°C 0.20 0. (V) D Figure 17. Slew Rate ON vs. V 0.9 0.85 0.8 0.75 0.7 0.65 0.6 0.55 0.5 0.45 ...
Page 10
TYPICAL CHARACTERISTICS CURVES 0 −1 −2 −3 −4 − TEMPERATURE (°C) Figure 23. Status Clamp Voltage (Negative) vs. Temperature 48 47.5 −40°C 47 25°C 46.5 150°C 46 45.5 45 44 ...
Page 11
TYPICAL CHARACTERISTICS CURVES 1000 100 10 10 Figure 29. Single−Pulse Maximum Switch−off ISO 7637−2: 2004(E) PULSE TEST RESULTS ISO 7637−2:2004(E) Test Pulse (Load Dump) ISO 7637−2:2004(E) Test Pulse ...
Page 12
Input Load Voltage Status Input Load Voltage Status V < Input Load Voltage Status Input Load Voltage V OL Status Input Load Voltage Status Input Load Voltage ...
Page 13
V STAT Input Reverse Battery Protection Reverse Battery Protection An external resistor R is required to adequately GND protect the device from a Reverse Battery event. The resistor value can be calculated using the following two formulas. ≥ 600 ...
Page 14
V STAT Input OFF State Open Load Detection Off State Open Load Detection requires an external pull-up resistor (R ) connected between V pull-up a positive supply voltage (V ). pull-up The external R resistor value should be selected ...
Page 15
Duty Cycle = 0.5 0.2 0.1 10 0.05 0.02 1 0.01 0.1 Single Pulse 0.01 0.000001 0.00001 0.0001 180 160 140 120 100 0.001 0.01 0.1 PULSE TIME (s) Figure 33. Transient Thermal Impedance 1.0 ...
Page 16
0.25 (0.010 −Y− −Z− 0.25 (0.010 *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting ...