BTS441R_09 INFINEON [Infineon Technologies AG], BTS441R_09 Datasheet
BTS441R_09
Related parts for BTS441R_09
BTS441R_09 Summary of contents
Page 1
Smart Power High-Side-Switch One Channel: 20 mΩ Smart Highside Power Switch One Channel: 20m Status Feedback Product Summary On-state Resistance Operating Voltage Nominal load current Current limitation General Description • N channel vertical power FET with charge pump, ground referenced ...
Page 2
Data sheet PROFET 2 BTS441R Rev. 1.1, 2009-01-30 ...
Page 3
Maximum Ratings °C unless otherwise specified j Parameter Supply voltage (overvoltage protection see page 4) Supply voltage for full short circuit protection T =-40 ...+150°C j Start Load dump protection 1) V LoadDump = 2 Ω, ...
Page 4
Electrical Characteristics Parameter and Conditions at T =-40...+150° unless otherwise specified j bb Load Switching Capabilities and Characteristics On-state resistance (V bb (pin3) to OUT (pin5) ≥ see ...
Page 5
Parameter and Conditions at T =-40...+150° unless otherwise specified j bb Protection Functions 10) Current limit (pin (see timing diagrams, page 9) Repetitive short circuit current limit (see timing diagrams, ...
Page 6
Parameter and Conditions at T =-40...+150° unless otherwise specified j bb Diagnostic Characteristics Open load detection voltage Input and Status Feedback Input resistance Input turn-on threshold voltage Input turn-off threshold voltage Input threshold hysteresis Off state ...
Page 7
Terms Input circuit (ESD protection) The use of ESD zener diodes as voltage clamp at DC conditions is not recommended. Status output ESD-Zener diode: 6.1 V typ., max 5.0 mA 1.6 mA, ESD zener diodes are not to ...
Page 8
GND disconnect with GND pull up Any kind of load device stays off GND > IN IN(T+) Due to V > low signal available. GND ST V disconnect with charged inductive ...
Page 9
Typ. on-state resistance high L R [mΩ] ON Typ. standby current , I RII M = 9...34 V, IN1,2 = low bb I ...
Page 10
Timing diagrams Figure 1a: V turn on: bb proper turn on under all conditions Figure 2a: Switching a resistive load, turn-on/off time and slew rate definition: on Data sheet Figure 2b: Switching a lamp, Figure 3a: Short circuit shut down ...
Page 11
Figure 4a: Overtemperature: Reset if T < Figure 5a: Open load: detection in OFF-state, turn on/off to open load 500µs ST delay Open load detection requires an external pull up resistor between OUT and ...
Page 12
Package Outlines 0...0.3 C 0...0.15 1) Typical Metal surface min 7.25 12.3 All metal surfaces tin plated, except area of cut. Figure 6: PG-TO220-5-12 Green Product (RoHS compliant) To meet the world-wide customer requirements for environmentally ...
Page 13
Typical Metal surface min 7.25 6.9 All metal surfaces tin plated, except area of cut. Figure 7: PG-TO263-5-2 Green Product (RoHS compliant) To meet the world-wide customer requirements for environmentally ...
Page 14
Revision History Revision Date Changes 1.1 2009-01-30 RoHS-compliant PG-TO220 and PG-TO263 packages version of the BTS441R All pages: Infineon logo updated Page 1: Added “AEC Qualified” and “RoHS” logo, added “Green Product (RoHS compliant)” and “AEC Qualified” statement to feature ...
Page 15
Edition 2009-01-30 Published by Infineon Technologies AG 81726 Munich, Germany 2009 Infineon Technologies AG © All Rights Reserved. Legal Disclaimer The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics. With ...