NCP562 ONSEMI [ON Semiconductor], NCP562 Datasheet
NCP562
Available stocks
Related parts for NCP562
NCP562 Summary of contents
Page 1
... The NCP562 series provides an enable pin for ON/OFF control. The NCP562 has been designed to be used with low cost ceramic capacitors and requires a minimum output capacitor of 0.1 mF. The device is housed in the micro−miniature SC82−AB surface mount package ...
Page 2
... If this function is not used, Enable should be connected to Vin. − 4 N/C No internal connection. MAXIMUM RATINGS Rating Input Voltage Enable Voltage (NCP562 ONLY) Output Voltage Power Dissipation and Thermal Characteristics Power Dissipation Thermal Resistance, Junction to Ambient Operating Junction Temperature Operating Ambient Temperature Storage Temperature 1. This device series contains ESD protection and exceeds the following tests: Human Body Model 2000 V per MIL− ...
Page 3
... V−5 6 Output Voltage Noise (f = 100 Hz to 100 kHz, V Enable Input Threshold Voltage (NCP562 ONLY) (Voltage Increasing, Output Turns On, Logic High) (Voltage Decreasing, Output Turns Off, Logic Low) Output Voltage Temperature Coefficient 3. Maximum package power dissipation limits must be observed. ...
Page 4
... Figure 6. Output Voltage versus Input Voltage LOAD LOAD LOAD 0 75 100 125 0 50 Figure 8. Turn−On Response (NCP562 ONLY) http://onsemi.com INPUT VOLTAGE (V) IN Voltage INPUT VOLTAGE ( ...
Page 5
... −30 400 200 OUT −200 V = 3.0 V OUT −400 0 100 200 300 400 500 600 t, TIME (ms) Figure 11. Load Transient Response NCP562, NCP563 −30 1 0.5 0 −0.5 −1 400 450 500 0 50 100 Figure 10. Load Transient Response 3 2.5 2 1.5 1 0.5 0 ...
Page 6
... IC operation, bias, etc. When the LDO becomes loaded, this term is called the Ground current actually the difference between the input current (measured through the LDO input pin) and the output current. NCP562, NCP563 DEFINITIONS Line Regulation The change in output voltage for a change in input voltage. ...
Page 7
... P tot + [ gnd (I out ) ] ) [ out ] * I out or V inMAX + output current is needed then the ground current from the data sheet is 2.5 mA. For an NCP562 or NCP563 (3.0 V), the maximum input voltage will then be 6.0 V. http://onsemi.com 7 T J(max ...
Page 8
... NCP563SQ27T1 NCP563SQ27T1G NCP563SQ28T1 NCP563SQ28T1G NCP563SQ30T1 NCP563SQ30T1G NCP563SQ33T1 NCP563SQ33T1G NCP563SQ50T1 NCP563SQ50T1G †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. NCP562, NCP563 ORDERING INFORMATION Marking 1.5 LDI 1.5 LDI 1.8 LEY 1.8 LEY 2.5 LDK 2 ...
Page 9
... NCP562, NCP563 PACKAGE DIMENSIONS SC82−AB (SC70−4) SQ SUFFIX CASE 419C−02 ISSUE C NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. 419C−01 OBSOLETE. NEW STANDARD IS 419C−02. 4. DIMENSIONS A AND B DO NOT INCLUDE ...
Page 10
... P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: orderlit@onsemi.com NCP562, NCP563 N. American Technical Support: 800−282−9855 Toll Free USA/Canada Japan: ON Semiconductor, Japan Customer Focus Center 2− ...