TL22CI CPI [Communications & Power Industries, Inc.], TL22CI Datasheet - Page 2

• Manufacturer Part Number: TL22CI
• Description: CPI 2.25 kW SuperLineartm TWT Amplifier
• Manufacturer: CPI [Communications & Power Industries, Inc.]

• Integral Linearizer
• Remote Control Panel
• Redundant and Power
• Extended Frequency
• External Receive Band
• Integral L-Band Block
C- Ba nd
For more detailed information, please refer to the corresponding CPI Technical Description.
Note: Specifi cations may change without notice as a result of additional data or product refi nement.
Please contact CPI before using this information for system design.
MKT 160, ISSUE 9
Combined Subsystems
(5.850 - 6.725 GHz or
5.725 - 6.525 GHz)
Reject Filter
Upconverter (BUC)
O P T I O N S &
C O M P A N I O N
P R O D U C T S :
02/08
Certificate Number: 30515
PDF
SPECIFICATIONS, TL22CI
Electrical
Frequency
Output Power
Bandwidth
Gain
RF Level Adjust
Output Power Adjustability
Gain Stability
Small Signal Gain Slope
Small Signal Gain Variation
Input/Output VSWR
Load VSWR
Residual AM, max.
Phase Noise
AM/PM Conversion
Harmonic Output
Noise and Spurious
Intermodulation
IESS-308/309
AC fundamentals related
Sum of spurs
with two equal carriers
TWT
phase noise continuous
Flange
1
1
5.85 - 6.65 GHz
2250 W min. (63.54 dBm)
1000 W max operating. (60.00 dBm)
800 MHz (1225 MHz optional)
75 dB min. at rated power output
78 dB min. at small signal
0 to 30 dB continuous
±0.1 dB
±0.25 dB/24 hr max.
(at constant drive and temp.)
0.02 dB/MHz max.
0.5 dB pk-pk max. over any 40 MHz;
1.0 dB pk-pk max. over any 40MHz
3.0 dB pk-pk max. across 800 MHz;
4.0 dB pk-pk max. across 800 MHz
5.0 dB pk-pk max. across 800 MHz
6.0 dB pk-pk max. across 800 MHz
1.25:1 max.
2.0:1 max. for full spec compliance;
any value without damage
-50 dBc below 10 kHz,
-20 (1.5 + log F kHz) dBc,
-85 dBc above 500 kHz
10 dB below mask at -10 dB backof
-50 dBc
-47 dBc
6°/dB max. With optional linearizer,
can be tuned to 2°/dB max.
-80 dBc
-150 dBW/4 kHz from 3.4 to 4.2 GHz
-65 dBW/4 kHz from 4.2 to 12.0 GHz
-60 dBW/4 kHz from 4.2 to 12.0 GHz
-110 dBW/4 kHz from 12.0 to 40.0 GHz
-23.5 dBc max, 5.850 - 6.425 GHz at
-22 dBc max. 6.425 - 6.650 GHz at
400 W without linearizer (-25 dBc max.
10 kHz to 500 kHz (F in kHz)
at 890 W with linearizer);
400 W without linearizer (-24 dBc max.
at 890 W with linearizer)
with linearizer option;
with linearizer option;
with BUC option;
with BUC and linearizer options
with linearizer option
Electrical (continued)
Group Delay
Primary Power
Power Factor
Power Consumption
Environmental
Ambient Temperature
Relative Humidity
Altitude
Shock and Vibration
Mechanical
Cooling(TWT)
RF Input Connection
RF Output Connection
RF Power Monitors
Dimensions (W x H x D)
Weight
1 Prime power AC line unbalance not to exceed 3%. Excess imbalance may cause
2 AC current harmonic content: less than 20%, primarily fifth and seventh harmonics. Harmonics
an increase in residual RF noise (AM, FM and PM). Phase noise increase is typically 2.5 dB / %
imbalance.
must be considered when choosing UPS sources.
(in any 40 MHz band)
2
0.01 ns/MHz linear
0.001 ns/MHz
0.5 ns pk-pk ripple max.
All ratings are ±10%, 47-63 Hz, 5-wire,
3-phase with neutral and ground
0.95 min.
5.0 kW max.;
4.5 kW typ. @ 1000 W linear RF output
3.8 kW typ. @ 800 W;
3.5 kW typ. @ 600 W;
3.3 kW typ. @ 400 W;
2.9 kW typ. @ 200 W;
2.5 kW typ. @ 100 W
-10° to +50°C operating
-20° to +70°C non-operating
95% non-condensing
Up to 10,000 ft (3000 m) with standard
adiabatic derating of 2°/1000 ft.;
50,000 feet non-operating
Designed for normal transportation
environment per Section 514.4
MIL-STD-810E. Designed to withstand
20g at 11 ms (1/2 sine pulse) in
non-operating condition
Forced air with integral blower
and power supply fan. Maximum
external pressure loss allowable:
0.25 inch water gauge.
Type N female
CPR 137 F waveguide fl ange,
grooved, threaded UNF 2B 10-32
Type N female
19 x 15.75 x 24 in.
(483 x 400 x 610 mm)
155 lbs. (70.5 kg) max.
power;
200 to 240 VAC (with or w/o neutral)
380 to 415 VAC
2
parabolic