ISL78200AVEZ INTERSIL [Intersil Corporation], ISL78200AVEZ Datasheet - Page 3

• Manufacturer Part Number: ISL78200AVEZ
• Description: 2.5A Regulator with Integrated High-Side MOSFET for Synchronous Buck or Boost Buck Converter
• Manufacturer: INTERSIL [Intersil Corporation]

Functional Pin Description
Ordering Information
NOTES:
ISL78200AVEZ
1. Add “-T*” suffix for tape and reel. Please refer to
2. These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte
3. For Moisture Sensitivity Level (MSL), please see device information page for ISL78200. For more information on MSL please see techbrief TB363.
EXT_BOOST
PIN NAME
PHASE
tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil
Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
LGATE
SYNC
PD
(Notes 1, 2, 3)
NUMBER
PART
16, 17
PIN #
18
19
20
21
This pin can be used to synchronize two or more ISL78200 controllers. Multiple ISL78200 can be synchronized with their SYNC
These pins are the PHASE nodes that should be connected to the output inductor. These pins are connected to the source of
the high side N channel MOSFET.
This pin is used to set boost mode and monitor the battery voltage that is the input of the boost converter. After VCC POR, the
controller will detect the voltage on this pin, if voltage on this pin is below 200mV, the controller is set in
synchronous/non-synchronous buck mode and latch in this state unless VCC is below the POR falling threshold; if the voltage
on this pin after VCC POR is above 200mV, the controller is set in boost mode and latch in this state.
In boost mode, this pin is used to monitor input voltage through a resistor divider. By setting the resistor divider, the high
threshold and hysteresis can be programmed. When voltage on this pin is above 0.8V , the PWM output (LGATE) for the boost
converter is disabled, and when voltage on this pin is below 0.8V minus the hysteresis, the boost PWM is enabled.
In boost mode operation, PFM is disabled when boost PWM is enabled. Check Boost Mode Operation in the “Functional
Description” on page 13 for more details.
pins connected together. 180 degree phase shift is automatically generated between the master and slave ICs.
The internal oscillator can also lock to an external frequency source applied on this pin with square pulse waveform (with
frequency 10% higher than the IC’s local frequency, and pulse width higher than 150ns).
This pin should be left floating if not used. Range: 0V to 5.5V.
In synchronous buck mode, this pin is used to drive the lower side MOSFET to improve efficiency.
In non-synchronous buck when a diode is used as the bottom side power device, this pin should be connected to VCC before
VCC start-up to have low side driver (LGATE) disabled.
In boost mode, it can be used to drive the boost power MOSFET. The boost control PWM is the same with the buck control PWM.
Bottom thermal pad. It is not connected to any electrical potential of the IC. In layout it must be connected to PCB ground
copper plane with an area as large as possible to effectively reduce the thermal impedance.
ISL78200 AVEZ
3
MARKING
PART
TB347
(Continued)
for details on reel specifications.
ISL78200
-40 to +105
RANGE
TEMP.
(°C)
DESCRIPTION
20 Ld HTSSOP
PACKAGE
(Pb-Free)
MDP0048
September 22, 2011
DWG. #
PKG.
FN7641.0