X9C102_06 INTERSIL [Intersil Corporation], X9C102_06 Datasheet

X9C102_06

Manufacturer Part Number

X9C102_06

Description

Digitally Controlled Potentiometer

Manufacturer

INTERSIL [Intersil Corporation]

Datasheet

1.X9C102_06.pdf (11 pages)

Current page: 1 of 11
Download datasheet (249Kb)

Digitally Controlled Potentiometer

(XDCP™)

FEATURES

• Solid-state potentiometer

• 3-wire serial interface

• 100 wiper tap points

• 99 resistive elements

• Low power CMOS

• High reliability

• X9C102 = 1kΩ

• X9C103 = 10kΩ

• X9C503 = 50kΩ

• X9C104 = 100kΩ

• Packages

• Pb-free plus anneal available (RoHS compliant)

BLOCK DIAGRAM

Device

Select

—Wiper position stored in nonvolatile memory

—Temperature compensated

—End to end resistance, ±20%

—Terminal voltages, ±5V

—V

—Active current, 3mA max.

—Standby current, 750µA max.

—Endurance, 100,000 data changes per bit

—Register data retention, 100 years

—8 Ld SOIC and 8 Ld PDIP

Increment

Up/Down

and recalled on power-up

(U/D)

(INC)

(CS)

= 5V

Memory

Control

(Supply Voltage)

and

General

(Ground)

Data Sheet

GND

U/D

INC

1-888-INTERSIL or 1-888-468-3774

Nonvolatile

Store and

CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.

Up/Down

Circuitry

Counter

Memory

Control

Recall

7-Bit

X9C102, X9C103, X9C104, X9C503

DESCRIPTION

The X9Cxxx are Intersil digitally controlled (XDCP)

potentiometers. The device consists of a resistor

array, wiper switches, a control section, and nonvola-

tile memory. The wiper position is controlled by a

three-wire interface.

The potentiometer is implemented by a resistor array

composed of 99 resistive elements and a wiper switch-

ing network. Between each element and at either end

are tap points accessible to the wiper terminal. The

position of the wiper element is controlled by the CS,

U/D, and INC inputs. The position of the wiper can be

stored in nonvolatile memory and then be recalled

upon a subsequent power-up operation.

The device can be used as a three-terminal potentiom-

eter or as a two-terminal variable resistor in a wide

variety of applications including:

– control

– parameter adjustments

– signal processing

December 20, 2006

Hundred

Decoder

One-

One

All other trademarks mentioned are the property of their respective owners.

Detailed

Intersil (and design) is a registered trademark of Intersil Americas Inc.

Transfer

Gates

Resistor

Array

FN8222.1

Related parts for X9C102_06

X9C102_06 Summary of contents

Page 1

Data Sheet Digitally Controlled Potentiometer (XDCP™) FEATURES • Solid-state potentiometer • 3-wire serial interface • 100 wiper tap points —Wiper position stored in nonvolatile memory and recalled on power-up • 99 resistive elements —Temperature compensated —End to end resistance, ...

Page 2

PIN CONFIGURATION ORDERING INFORMATION PART NUMBER PART MARKING X9C102P X9C102P X9C102PZ (Note) X9C102P Z X9C102PI X9C102P I X9C102PIZ (Note) X9C102P ZI , X9C102S* ** X9C102S X9C102SZ* (Note) X9C102S Z , X9C102SI* ** X9C102S I , X9C102SIZ* ** (Note) X9C102S ZI ...

Page 3

PIN DESCRIPTIONS Pin Symbol 1 INC Increment . The INC input is negative-edge triggered. Toggling INC will move the wiper and either increment or decrement the counter in the direction indicated by the logic level on the U/D input. 2 ...

Page 4

ABSOLUTE MAXIMUM RATINGS Temperature under bias .................... -65°C to +135°C Storage temperature ......................... -65°C to +150°C Voltage on CS, INC, U/D and V CC with respect to V .................................. -1V to +7V SS Voltage and V /R ...

Page 5

D.C. OPERATING CHARACTERISTICS (Over recommended operating conditions unless otherwise specified.) Symbol Parameter I V active current Standby supply current SB I CS, INC, U/D input leakage LI current V CS, INC, U/D input HIGH IH voltage V ...

Page 6

A.C. OPERATING CHARACTERISTICS (Over recommended operating conditions unless otherwise specified) Symbol Parameter INC setup Cl t INC HIGH to U/D change lD t U/D to INC setup DI t INC LOW period lL t INC HIGH period ...

Page 7

DETAILED PIN DESCRIPTIONS R /V and The high ( and low ( X9C102/103/104/503 are equivalent to the fixed termi- nals of a mechanical potentiometer. The minimum voltage is ...

Page 8

INSTRUCTIONS AND PROGRAMMING The INC, U/D and CS inputs control the movement of the wiper along the resistor array. With CS set LOW the device is selected and enabled to respond to the U/D and INC inputs. HIGH to LOW ...

Page 9

PERFORMANCE CHARACTERISTICS Contact the factory for more information. APPLICATIONS INFORMATION Electronic digitally controlled (XCDP) potentiometers provide three powerful application advantages; (1) the variability and reliability of a solid-state potentiometer, (2) the flexibility of computer-based digital controls, and (3) the retentivity ...

Page 10

Small Outline Package Family (SO PIN #1 I.D. MARK 0.010 SEATING PLANE 0.004 C 0.010 MDP0027 SMALL OUTLINE PACKAGE FAMILY (SO) SYMBOL SO-8 SO-14 ...

Page 11

Plastic Dual-In-Line Packages (PDIP) D SEATING PLANE MDP0031 PLASTIC DUAL-IN-LINE PACKAGE SYMBOL PDIP8 PDIP14 A 0.210 0.210 A1 0.015 0.015 A2 0.130 0.130 b 0.018 0.018 b2 0.060 0.060 c 0.010 0.010 D 0.375 0.750 E 0.310 ...

Related keywords

X9C102_06 datasheet
X9C102_06 data sheet
X9C102_06 pdf datasheet
X9C102_06 component
X9C102_06 part
X9C102_06 distributor
X9C102_06 RoHS
X9C102_06 datasheet download