LTC3210-3 LINER [Linear Technology], LTC3210-3 Datasheet - Page 3

• Manufacturer Part Number: LTC3210-3
• Manufacturer: LINER [Linear Technology]

ELECTRICAL CHARACTERISTICS
temperature range, otherwise specifi cations are at T
ENM = high, unless otherwise noted.
PARAMETER
MLED Current, 5-Bit Linear DAC
CLED Current
LED Current Ratio (I
LED Dropout Voltage
CLED Current, 3-Bit Linear DAC
Charge Pump (CPO)
1x Mode Output Voltage
1.5x Mode Output Voltage
2x Mode Output Voltage
1x Mode Output Impedance
1.5x Mode Output Impedance
2x Mode Output Impedance
CLOCK Frequency
Mode Switching Delay
CPO Short Circuit Detection
Threshold Voltage
Test Current
ENC, ENM
V
V
I
I
ENC, ENM Timing
t
t
t
RM, RC
V
I
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: Based on long-term current density limitations. Assumes an
operating duty cycle of ≤10% under absolute maximum conditions
for durations less than 10 seconds. Maximum current for continuous
operation is 300mA.
IH
IL
PW
SD
EN
RM
IL
IH
RM
, I
, V
RC
RC
CLED
/I
RC
)
CONDITIONS
1 ENM Strobe (FS)
31 ENM Strobes (FS/31)
I
Mode Switch Threshold, I
1 ENC Strobe (FS)
7 ENC Strobes (FS/7)
I
I
I
V
V
CPO = 0V, ENM = ENC = Low
ENM = ENC = 3.6V
ENM = ENC = 0V
Minimum Pulse Width
Low Time to Shutdown (ENC, ENM = Low)
Current Source Enable Time
(ENC, ENM = High) (Note 5)
CLED
CPO
CPO
CPO
BAT
BAT
A
= 25°C.V
= 0mA
= 0mA
= 0mA
= 3.4V, V
= 3.2V, V
= Full Scale
The
BAT
●
CPO
CPO
denotes the specifi cations which apply over the full operating
= 3.6V, C1 = C2 = C3 = C4 = 2.2μF, RM = 30.1k, RC = 24.3k,
= 4.6V (Note 4)
= 5.1V (Note 4)
Note 3: The LTC3210-2/LTC3210-3 are guaranteed to meet performance
specifi cations from 0°C to 70°C. Specifi cations over the –40°C to
85°C ambient operating temperature range are assured by design,
characterization and correlation with statistical process controls.
Note 4: 1.5x mode output impedance is defi ned as (1.5V
2x mode output impedance is defi ned as (2V
Note 5: If the part has been shut down then the initial enable time is about
100μs longer due to the bandgap enable time.
CLED
= Full Scale
LTC3210-2/LTC3210-3
●
●
●
●
●
●
●
●
●
●
●
●
6930
1.16
MIN
200
0.4
1.4
10
10
–1
50
50
BAT
0.640
7700
V
4.55
5.05
0.55
3.15
3.95
1.20
TYP
500
380
150
150
0.8
0.4
20
54
15
– V
BAT
CPO
)/I
BAT
OUT
8470
MAX
1.24
250
250
1.3
0.4
30
20
80
1
– V
.
CPO
)/I
321023fa
UNITS
OUT
3
MHz
A/A
mA
mA
mV
mA
mA
mA
ms
μA
μA
μA
ns
μs
μs
.
Ω
Ω
Ω
V
V
V
V
V
V
V