US3010ACW UNISEM [UNISEM], US3010ACW Datasheet - Page 4

• Manufacturer Part Number: US3010ACW
• Description: 5 BIT PROGRAMMABLE SYNCHRONOUS BUCK CONTROLLER IC
• Manufacturer: UNISEM [UNISEM]

US3010/3010A
PIN DESCRIPTIONS
PIN DESCRIPTIONS
4-4
PIN# PIN SYMBOL
20
19
18
17
16
4
15
6
5
13
1
10
11
8
12
2
3
14
7,9
D0
D1
D2
D3
D4
PGd
Vfb
CS+
CS-
SS
Ct
Gnd
LDrv
HDrv
V12
V5
OVP
OUTEN
NC
Pin Description
LSB input to the DAC that programs the output voltage. This pin can be pulled up exter-
nally by a 10k resistor to either 3.3V or 5V supply.
Input to the DAC that programs the output voltage.This pin can be pulled up externally by
a 10k resistor to either 3.3V or 5V supply.
Input to the DAC that programs the output voltage.This pin can be pulled up externally by
a 10k resistor to either 3.3V or 5V supply.
MSB input to the DAC that programs the output voltage.This pin can be pulled up exter-
nally by a 10k resistor to either 3.3V or 5V supply.
This pin selects a range of output voltages for the DAC. The voltage range for both the "A"
and the none "A" versions of the device is given in table 1.
This pin is an open collector output that switches LO when the output of the converter is
not within 10% (typ) of the nominal output voltage.When PWRGD pin switches LO the
sat voltage is less than 0.4V at 3mA.
This pin is connected directly to the output of the Core supply to provide feedback to the
Error comparator.
This pin is connected to the Drain of the power MOSFET of the Core supply and it
provides the positive sensing for the internal current sensing circuitry. An external resis-
tor programs the C.S threshold depending on the Rds of the power MOSFET. An external
capacitor is placed in parallel with the programming resistor to provide high frequency
noise filtering.
This pin is connected to the Source of the power MOSFET for the Core supply and it
provides the negative sensing for the internal current sensing circuitry.
This pin provides the soft start for the switching regulator. An internal current source
charges an external capacitor that is conected from this pin to the GND which ramps up
the outputs of the switching regulator, preventing the outputs from overshooting as wellas
limiting the input current. The second function of the Soft Start cap is to provide long off
time for the synchronous MOSFET or the Catch diode (HICCUP) during current limiting.
This pin programs the oscillator frequency in the range of 50 kHZ to 500kHZ with an
external capacitor connected from this pin to the GND.
This pin serves as the ground pin and must be conected directly to the ground plane. A
high frequency capacitor (0.1 to 1 uF) must be connected from V5 and V12 pins to this
pin for noise free operation.
Output driver for the synchronous power MOSFET.
Output driver for the high side power MOSFET.
This pin is connected to the 12 V supply and serves as the power Vcc pin for the output
drivers.A high frequency capacitor (0.1 to 1 uF) must be connected directly from this pin
to GND pin in order to supply the peak current to the power MOSFET during the transi-
tions.
5V supply voltage.
Over voltage comparator output.
This is the output enable pin.This pin is internally pulled high through a 35k resistor to
5V supply. A low signal on this pin disables the output.
No connect.
Rev. 1.1
5/18/98